ABB 1ZSC902110-AAA Installation And Commissioning Manual Download | Manualshive

Page: 11 / 84

background image

Installation and commissioning guide
1ZSC000563-AAF EN, REV. 4, 2021-06-23

11

List of bushings applicable to this installation guide

Type

Article number

GOE 2600

LF121085-D

GOE 2600

1ZSC902110-AAA

2.2.2 Mechanical loading

Maximum permitted static load on the outer terminal

The load must be applied below the midpoint of the outer terminal. The total cantilever load must be
perpendicular to the bushing axis. The bushing installation angle can be 0° – 30° from vertical.

NOTE!

The loads described in this section are static loads, for dynamic loads such as earthquakes and
extreme wheather conditions, please contact your Hitachi ABB Power Grids sales representative.

G006946

A.

Maximum cantilever load at installation angle 0°

B.

Maximum axial static load

C.

Load applied at the midpoint

Type

Test load 1 minute
(N)

Maximum cantilever load in operation
at installation angle (N)

Maximum axial
static load (N)

0°

>0°

GOE 2600

9500

2500

On request.

20000

Maximum permitted torque on the outer terminal

The maximum torque that is permitted on the outer terminal is 250 Nm.

«
...
9
10
11
12
13
...
»

Summary of Contents for 1ZSC902110-AAA





















































































Reviews:

No comments

Related manuals for 1ZSC902110-AAA

Brand: ParaBody Pages: 5

Brand: Sagola Pages: 20

Brand: Earmor Pages: 5

Brand: Abbott Pages: 2

FreeStyle Libre

Brand: Abbott Pages: 3

Brand: abc Pages: 8

Brand: Tascam Pages: 80

Brand: Tascam Pages: 2

Brand: Walker Pages: 24

Brand: Cameo Pages: 64

Brand: Cameo Pages: 100

Brand: CAME Pages: 32

Brand: Konica Minolta Pages: 32

Brand: Nectar Pages: 46

Brand: Neauvia Pages: 17

HQ Power VDL25BM

Brand: Velleman Pages: 3

Brand: iGuzzini Pages: 36

AQUIS ULTRAFLOW

Brand: Waterous Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands