ABB Robotics IRB 4600 Manual Download

Page: 63 / 400

Note

Dimension

Securing parts/Facts

Article number: 21510024-
169, 2 pcs.

Guide bushings

Added to the rear bolt holes,
to allow the same robot to be
re-mounted without program
adjustments.

xx1200000885

xx0300000251

Level surface requirements

Orienting and securing the robot

Use this procedure to orient and secure the robot.

Note

Action

Make sure the installation site for the robot
conforms to the specifications in section

Pre-

installation procedure on page 44

Hole configuration of the base is shown
in the figure in:

•

Hole configuration, base on
page 61

Prepare the installation site with attachment
holes.

CAUTION

The IRB 4600 robot weighs 440 kg.
All lifting accessories used must be sized
accordingly!

CAUTION

When the robot is put down after being lifted
or transported, there is a risk of it tipping, if
not properly secured.

How to lift the robot is described in sec-
tion:

•

Lifting robot with roundslings on
page 54

Lift the robot to its installation site.

Fit two

guide bushings

to the

rear bolts

in the

base.

Make sure the robot base is correctly fit-
ted onto the guide sleeves.

Guide the robot gently, using the attachment
screws while lowering it into its mounting
position.

Continues on next page

Product manual - IRB 4600

3HAC033453-001 Revision: Y

2 Installation and commissioning

2.3.4 Orienting and securing the robot

Continued

Summary of Contents for IRB 4600

















































































































































































































































































































































































































Search results

Summary of Contents for IRB 4600

Reviews:

Related manuals for IRB 4600

Brands by name

Popular brands

ABB Robotics IRB 4600, Manual

Search results

Summary of Contents for IRB 4600

Reviews:

Related manuals for IRB 4600

Brands by name

Popular brands