ABACUS HL250 Page 15 Product Manual Download | Manualshive

Page: 15 / 24

background image

Abacus Lighting, Sutton-in-Ashfield, Nottinghamshire, NG17 5FT, England. Tel: (+44) 01623 511111, www.abacuslighting.com

14



4.

Maintenance

4.1.

Mast Type Identification

These masts are of galvanised steel construction with tapering slip joint type octagonal shafts.
They can be identified by measuring the width of the base at flange level. The width should be
approximately 250mm on the HL250 and 330mm on the HL330. The illustrations below show the
typical arrangement of the HL250 and HL330 mast bases.

HL250

HL330

Maintenance requirements are minimal but the following checks are recommended at the
intervals stated.

«
...
13
14
15
16
17
...
»

Summary of Contents for HL250

























Reviews:

No comments

Related manuals for HL250

5505-0-3-873 Series

Brand: Unilamp Pages: 3

Brand: IBEX Pages: 6

Brand: Ballard Designs Pages: 4

Brand: Badger Basket Pages: 6

Brand: urban ambiance Pages: 3

PROforce Series

Brand: PROformance Hoops Pages: 8

Brand: MARIMEX Pages: 60

Barrington 2206045

Brand: Backyard Discovery Pages: 77

Brand: Belson Outdoors Pages: 7

Brand: Carromco Pages: 6

Brand: Weka Pages: 28

Brand: PHI VILLA Pages: 4

Rittenhouse Rittenhouse

Brand: Campania International Pages: 2

Brand: Alice's Garden Pages: 8

Brand: FK SKS Pages: 2

Litetower Series

Brand: Exterior Lights Pages: 2

Brand: Airmax Pages: 4

Brand: Campania International Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands