Aastra BE-100HT Owner'S Manual Download Page 14

- 14 - 

When using your telephone, basic safety precautions should always 
be followed to reduce the risk of fire, electrical shock, and/or injury to 
persons including the following: 
 
1. Read and understand all instructions. 
2. Follow all warnings and instructions marked on the product. 
3. Do not use liquid cleaners, or aerosol cleaners. Use a damp cloth for 

cleaning. If necessary, use a mild soap. 

4. Do not use this product near water, for example near a bath tub, 

wash bowl, kitchen sink, or laundry tub, in a wet basement, or near 
a swimming pool. 

5. Do not place this product on an unstable cart, stand or table. The 

product may fall, causing serious damage to the product. 

6. Do not allow anything to rest on the telephone line cord. Do not 

locate this product where the cord will be abused by persons 
walking on it. 

7. Never spill liquid of any kind on the product. 
8. To reduce the risk of electric shock, do not disassemble this 

product. If servicing is required, take it to a qualified serviceman. 

9. Disconnect this product from the telephone line and refer to 

qualified service personnel under the following conditions: 

 
a. If liquid has been spilled into the product. 
b. If the product has been exposed to rain or water. 
c. If the product has been dropped or the cabinet has been damaged. 
d. If the product exhibits a distinct change in performance. 
e. If the product does not operate normally by following the operating 

instructions. Adjust only those controls, that are covered by the 
operating instructions because improper adjustment of other 
controls may result in damage and will often require extensive work 
by a qualified technician to restore the product to normal operation. 

 

10. Avoid using a telephone (other than a cordless type) during an 

electrical storm. There may be a remote risk of electrical shock 
from lightning. 

11. Do not use the telephone to report a gas leak in the vicinity of the 

leak. 

IMPORTANT SAFETY INFORMATION 

Summary of Contents for BE-100HT















Reviews: