TRX MAINS Output Assignment
Advance Output Mapping (requires IR Remote-10)
The Default Assigned Output for the TRX MAINS is 8, to change this please follow the steps below:
1– Safely apply power to the TRX MAINS
2- Point the IR remote at the bottom of the TRX MAINS and press P followed by the Output you wish to
Map it to (1-8) then E. The TRX MAINS should give a triple beep indicating this was successful.
Note. It is not recommended to Map to Output 1 or 2 as they are for Sirens by default.
3- Make a note of this number here and on the TRX MAINS.
Note. Multiple TRX MAINS can be paired to the same Output.
*With an Output Assigned in to the TRX MAINS it’s Trigger Input is not Directly linked to the Switched Output.
If you wish the Trigger Input to activate the Switched Output you must program it into the Elite S Panel.
=
Programming Trigger Input to Switched Output Link
with ESL Control Board
The ESL v908.12c has pre assigned slots for the TRX Mains devices.
If you have an Elite-S or Elite-S-Lite Control board v908.12b or older please use programming on page 8
Follow the list below for the Addresses that relate to the TRX Mains Output number assigned:
*Programming below is done from the Control Panel Keypad in Installer Mode.
Default = 8
Page 7
=
3
1– Learn State 1 (ON) to the first User slot
P 18 E 90 E E (when beeping starts flick the switch connected to the TRX Mains On)
2– Learn State 2 (OFF) to the second User slot. if you have a momentary switch, skip this step
P 18 E 91 E E (when beeping starts flick the switch connected to the TRX Mains Off)
3– Adjusting Output Reset Time, the default reset time is only 2 seconds.
P 40 E 3 E 0 E (lights now will not automatically turn off)
=
5
1– Learn State 1 (ON) to the first User slot
P 18 E 92 E E (when beeping starts flick the switch connected to the TRX Mains On)
2– Learn State 2 (OFF) to the second User slot. if you have a momentary switch, skip this step
P 18 E 93 E E (when beeping starts flick the switch connected to the TRX Mains Off)
3– Adjusting Output Reset Time, the default reset time is only 2 seconds.
P 40 E 5 E 0 E (lights now will not automatically turn off)
=
6
1– Learn State 1 (ON) to the first User slot
P 18 E 94 E E (when beeping starts flick the switch connected to the TRX Mains On)
2– Learn State 2 (OFF) to the second User slot. if you have a momentary switch, skip this step
P 18 E 95 E E (when beeping starts flick the switch connected to the TRX Mains Off)
3– Adjusting Output Reset Time, the default reset time is only 2 seconds.
P 40 E 6 E 0 E (lights now will not automatically turn off)
=
7
1– Learn State 1 (ON) to the first User slot
P 18 E 96 E E (when beeping starts flick the switch connected to the TRX Mains On)
2– Learn State 2 (OFF) to the second User slot. if you have a momentary switch, skip this step
P 18 E 97 E E (when beeping starts flick the switch connected to the TRX Mains Off)
3– Adjusting Output Reset Time, the default reset time is only 2 seconds.
P 40 E 7 E 0 E (lights now will not automatically turn off)
=
8
1– Learn State 1 (ON) to the first User slot
P 18 E 98 E E (when beeping starts flick the switch connected to the TRX Mains On)
2– Learn State 2 (OFF) to the second User slot. if you have a momentary switch, skip this step
P 18 E 99 E E (when beeping starts flick the switch connected to the TRX Mains Off)
3– Adjusting Output Reset Time, the default reset time is only 2 seconds.
P 40 E 8 E 0 E (lights now will not automatically turn off)
