background image

DIALLER SETUP - 

FOR PERSONAL MONITORING  

 

If you have an Analogue telephone line connected to the panel, the built-in Domestic Dial option can be chosen. 
In Domestic Dial the Alarm will call a cellphone or land-line and play a siren tone down the line in the event of an 
alarm activation. The call then needs to be acknowledged by pressing the # key on the phone hand set. 

The ESL control panel has 4 telephone number slot (5 to 8) setup and ready for Domestic Dial. 
 

Note. Do Not use number slots 1,2,3 or 4 these are for Monitoring station use only 

  
Telephone number  5    [   ][   ][   ][   ][   ][   ][   ][   ][   ][   ][   ] (domestic dial slot 1) 

Telephone number  6    [   ][   ][   ][   ][   ][   ][   ][   ][   ][   ][   ] (domestic dial slot 2) 
Telephone number  7    [   ][   ][   ][   ][   ][   ][   ][   ][   ][   ][   ] (domestic dial slot 3) 
Telephone number  8    [   ][   ][   ][   ][   ][   ][   ][   ][   ][   ][   ] (domestic dial slot 4) 

 

Step 1: 

Connect across the incoming phone line between the street and the first jack point.  

 
Step 2: 

Enable the dialler. In Installer Mode press <PROGRAM> <175> <ENTER> <1> <ENTER> 

 

 

(then turn ON option 1) and <ENTER>. 

 

 

i.e. P 175 E 1 E 1 E     

 
Step 3:  

Adding Phone Numbers, In Installer Mode press <PROGRAM> <181> <ENTER> <5-8>  

 

 

<ENTER> (now key in your phone number) and <ENTER>.  

 

 

P 181 E 5 E  [   ][   ][   ][   ][   ][   ][   ][   ][   ][   ][   ][   ]   E  

 

 

 

P 181 E 6 E  [   ][   ][   ][   ][   ][   ][   ][   ][   ][   ][   ][   ]   E  

 

 

 

 

P 181 E 7 E  [   ][   ][   ][   ][   ][   ][   ][   ][   ][   ][   ][   ]   E  

 

 

 

 

P 181 E 8 E  [   ][   ][   ][   ][   ][   ][   ][   ][   ][   ][   ][   ]   E  

 

 

 

 

i.e.  P 181 E 5 E 021555123 E (the first domestic dial phone number would be 021555123) 

 
Step 4: 

Exit program mode by pressing and holding <PROGRAM>  

 
Step 5 : 

Testing. With the phone learnt into slot 1 on hand, Arm the panel and wait for the exit delay to  

 

 

finish. Then walk in front of a PIR, the entry delay should start, followed by the sirens sounding.  

 

 

Disarm the panel to make the sirens stop. The phone should now be ringing, answer it and listen. 

 

 

A siren tone should play for 3 seconds on 2 seconds off. While the tone is off press and hold the # 

 

 

key to acknowledge the call, the alarm panel will then hang up. (if the # key will not hang up the 

 

 

panel try a different key)   

 

 

Page 5 

What a more advanced personal monitoring option? 

Follow this QR Code link for our  

Smart Phone App Option  

Summary of Contents for QUICKFIT









Reviews: