AAON Orion ASM01819 Manual Download | Manualshive

Page: 16 / 24

background image

EBTRON

®

is a registered trademark of Ebtron, Inc., Loris, SC.

GreenTrol

TM

is a registered trademark of GreenTrol Automation, Inc. Loris, SC.

Paragon

®

is a registered trademark of Paragon Controls, Inc. Santa Rosa, CA.

E-BUS Adapter Board

ASM01878

ALT-REF number OE365-15-EBA

Description

The E-BUS Adapter Board is used to provide a
connection point for multiple E-BUS Sensors or
Modules.

The E-BUS Adapter Board is also used for
connecting an EBTRON

®

GTC116 or HTN104

Airflow Measurement Digital Transmitter, a
GreenTrol

TM

GA-200-N Transmitter Module with

GF Series Airflow Monitoring Station, or Paragon
MicroTrans

EQ

series MODBUS RTU Transmitter

to the VCCX2, VCB-X, VCM-X E-BUS, or various
other AAON Unit Controllers.

You must wire the EBTRON

®

, GreenTrol

TM

, or

Paragon* Airflow Measurement Digital
Transmitter to this Adapter Board.

The E-BUS Adapter Board has (4) Modular E-
BUS ports, (3) HSSC E-BUS Connections, and (2) MSTP
E-BUS Connections.

Mounting

The E-BUS Adapter Board is provided with a plastic snap track modular mounting base. The snap track is
designed to be mounted with the provided sheet metal screws to a flat surface. There is (1) pre-punched
mounting slot provided. The other screw may be drilled into the snap track to prevent rotation. The E-BUS
Adapter Board is then snapped into place on the snap track to provide for easy field mounting and servicing.

Technical Data

E-BUS Adapter Board

Terminations

(4) EBC Connections

(2) MSTP E-BUS Connections

(3) HSSC Connections

One Year Warranty

AAON reserves the right to change specifications without notice

«
...
14
15
16
17
18
...
»

Summary of Contents for Orion ASM01819

























Reviews:

No comments

Related manuals for Orion ASM01819

Brand: Gates Pages: 2

AJHVF21G - HD EVF - MULTI-LANG

Brand: Panasonic Pages: 4

Brand: Wagan Pages: 12

Brand: Kampmann Pages: 32

Brand: Valor Pages: 5

DS-KABD8003-RS3

Brand: HIKVISION Pages: 3

Brand: Gared Pages: 10

Brand: Snapper Pages: 1

Brand: Whispbar Pages: 16

Brand: Valor Fires Pages: 12

Brand: Cognex Pages: 39

Brand: Cardinal Pages: 52

Brand: Rice Lake Pages: 56

Brand: RCS Pages: 29

Brand: ViewSonic Pages: 2

Brand: Keith McMillen Instruments Pages: 89

LeisureWize EMOVE EM303A

Brand: Streetwize Pages: 20

Brand: Clatronic Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands