AAON OE377-26-00060-1 Technical Manual Download Page 26

Page: 26 / 40

LCD DISPLAY SCREENS

MODGAS-XWR-1 Technical Guide

Setpoint & Force Valve Screens

Force Valve Screens

Refer to the following map when navigating through the Force Valve
Screens. From the FORCE VALVE Screen, press

<ENTER>

At the

V1 and V2 FORCE ON/OFF screens, press the

<UP>

arrow key to

turn the FORCE MODE on and press the

<DOWN>

arrow key to turn

the FORCE MODE oﬀ . Use the

<UP>

and

<DOWN>

arrow keys to

increase and decrease the percentage.

FORCE

VALVES

STAGE 1 FORCE

ON/OFF

V1 POSITION

FORCE VALVE 1 PERCENTAGE

This screen only appears when Stage 1 Force is on.

Press the

<UP>

button to turn the Force Mode on. Press the

<DOWN>

button to turn the Force Mode oﬀ .

Press the

<UP>

button to increase the percentage. Press the

<DOWN>

button to decrease the percentage.

NOTE:

When you turn the Force Mode back oﬀ or after 10 minutes of no

keypad input, the valve will go to zero and the relays will turn oﬀ .

STAGE 2 FORCE

ON/OFF/DISABLED

V2 POSITION

FORCE VALVE 2 PERCENTAGE

This screen only appears when Valve 2 Force is on.

Press the

<UP>

button to turn the Force Mode on. Press the

<DOWN>

button to turn the Force Mode oﬀ . If the screen says disabled, on/oﬀ
selection is not possible.

Press the

<UP>

button to increase the percentage. Press the

<DOWN>

button to decrease the percentage.

STAGE 3

FORCE ON/OFF

STAGES 3 & 4 FORCE ON / OFF

The Stages Force Screens will allow you to force each stage on or oﬀ .

Press the

<UP>

button to turn the Force Mode on. Press the

<DOWN>

button to turn the Force Mode oﬀ .

STAGE 4

FORCE ON/OFF

RESET SP

40-200°F

5-93°C

RESET HEATING SUPPLY AIR SETPOINT

This is maximum temperature at which the Supply Air Temperature will
reset to. The Setpoint Screen will display only in stand-alone mode.

Minimum

Default

Maximum

40°F

5°C

120°F

49°C

200°F

93°C

Summary of Contents for OE377-26-00060-1








































Search results

Summary of Contents for OE377-26-00060-1

Reviews:

Related manuals for OE377-26-00060-1

Brands by name

Popular brands

AAON OE377-26-00060-1, Technical Manual

Search results

Summary of Contents for OE377-26-00060-1

Reviews:

Related manuals for OE377-26-00060-1

Brands by name

Popular brands