manualshive.com logo in svg

A&D FX-1200i, Instruction Manual

Share
Download
A&D FX-1200i Instruction Manual Download Page 10

 

3

1. INTRODUCTION 

This manual describes how the FX-

i

 WP

 

series balance works and how to get the most out of it in 

terms of performance.   
Read this manual thoroughly before using the balance and keep it at hand for future reference. 
 

1-1  About This Manual 

This manual consists of the following five parts:

 

Basic operation ........................ Describes precautions on handling the balance, balance 

construction and basic balance operation.   

Adapting to the environment.... Describes response adjustment and calibration. 
Functions ................................. Describes various functions of the balance. 
RS-232C serial interface.......... Describes the interface which transmits data and controls the balance. 
Maintenance ............................ Describes maintenance, error codes, troubleshooting, 

specifications and options. 

 

1-2 Features 

  Dust-tight and protected against water jets (complying with IP65), suitable to weigh powdery or 

liquid material. A waterproof RS-232C cable (AX-KO2737-500) is available as an option. 

 

Compact general-purpose balance, can be installed almost anywhere. 

 

Casing construction, strong protection against dust and water. 

  Stabilization time of one second. When FAST is selected for the response rate, a stabilization 

time of one second, to read a displayed value after a sample is placed on the pan, has been 
achieved.  

 

Multiple weighing units with most of the common units used around the world. 

  Standard RS-232C serial interface to communicate with a computer and to output the Good 

Laboratory Practice (GLP) data 

  Statistical calculation mode to statistically calculate the weight data, and display or output the 

sum, maximum, minimum, range (maximum-minimum), average, standard deviation and 
coefficient of variation. 

 

Comparator Indicators, displaying the comparison results. 

  Hold Function, provided for weighing a moving object such as an animal. 

 

Breeze break, provided for the FX-120

i 

WP /200

i 

WP /300

i 

WP, for more accurate weighing.   

  Underhook, provided for suspended weighing. 
  As options, the USB interface (FX

i

-02), the Ethernet interface (Fx

i

-08) and the built-in battery unit 

(Fx

i

-09) are available. When any one of these is used, the balance does not comply with IP65. 

 

 

 

 

 

 

 

 

Summary of Contents for FX-1200i
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands