Aaeon FWS-2275 User Manual Download Page 36 | Manualshive

Page: 36 / 99

Aaeon FWS-2275 User Manual Download Page 36

Chapter 3

–

AMI BIOS Setup

36

Deskt

op

Net
work

Ap

plian
ce

FW

S-

22

75

Options Summary

Platform Hierarchy

Disabled

Enabled

Default Setting

Enable or Disable Platform Hierarchy
Storage Hierarchy

Disabled

Enabled

Default Setting

Enable or Disable Storage Hierarchy
Endorsement Hierarchy

Disabled

Enabled

Default Setting

Enable or Disable Endorsement Hierarchy
TPM2.0 UEFI Spec Version

TCG_1_2

TCG_2

Default Setting

Select the TCG2 Spec Version Support,
TCG_1_2: Compatible mode for Win8/Win10,
TCG_2: Support new TCG2 protocol and event format for Win10 or later
Physical Presence Spec
Version

1.2

1.3

Default Setting

Select to Tell O.S. to support PPI Spec Version 1.2 or 1.3. Note some HCK tests might not
support 1.3.
Device Select

TPM 1.2

TPM 2.0

Auto

Default Setting

TPM 1.2 will restrict support to TPM 1.2 devices, TPM 2.0 will restrict support to TPM 2.0
devices, Auto will support both with the default set to TPM 2.0 devices if not found,
TPM 1.2 devices will be enumerated

«
...
34
35
36
37
38
...
»

Summary of Contents for FWS-2275




































































































Reviews:

No comments