background image

8

facts to consIder aBout the locatIon

Carefully choose an indoor location for the new water heater, because 

the placement is a very important consideration for the safety of the 

occupants in the building and for the most economical use of the 

appliance. 

this  water  heater  is  not  for  use  in  manufactured 

(mobile) homes or outdoor installation.

Whether replacing an old water heater or putting the water heater in 

a new location, the following critical points must be observed:

1.  Select a location indoors as close as practical to the vent terminal or 

location to which the water heater vent piping is going to be connected, 

and as centralized with the water piping system as possible.  

2.  Selected location must provide adequate clearances for servicing 

and proper operation of the water heater.

Installation  of  the  water  heater  must  be  accomplished  in  such  a 

manner that if the tank or any connections should leak, the flow will not 

cause damage to the structure. For this reason, it is not advisable to 

install the water heater in an attic or upper floor. When such locations 

cannot be avoided, a suitable drain pan should be installed under the 

water heater. Drain pans are available at your local hardware store.  

Such a drain pan must have a minimum length and width of at least 

2” (5.1 cm) greater that the water heater dimensions and must be 

piped to an adequate drain. Drain pan depth must allow for access 

to the outer doors for servicing the ignitor and burner.  

Water heater life depends upon water quality, water pressure and the 

environment in which the water heater is installed. Water heaters are 

sometimes installed in locations where leakage may result in property 

damage, even with the use of a drain pan piped to a drain. However, 

unanticipated damage can be reduced or prevented by a leak detector 

or water shut-off device used in conjunction with a piped drain pan. 

These devices are available from some plumbing supply wholesalers 

and retailers, and detect and react to leakage in various ways:

•  Sensors mounted in the drain pan that trigger an alarm or turn off the 

incoming water to the water heater when leakage is detected.

•  Sensors mounted in the drain pan that turn off the water supply to 

the entire home when water is detected in the drain pan.

•  Water supply shut-off devices that activate based on the water 

pressure differential between the cold water and hot water pipes 

connected to the water heater.

•  Devices that will turn off the gas supply to a gas water heater while 

at the same time shutting off its water supply.

INSTALLATIONS  IN AREAS  WHERE  FLAMMABLE  LIQUIDS 

(VAPORS) ARE LIKELY TO BE PRESENT OR STORED (GARAGES, 

STORAGE AND UTILITY AREAS, ETC.): Flammable liquids (such as 

gasoline, solvents, propane (LP or butane, etc.) and other substances 

(such as adhesives, etc.) emit flammable vapors which can be ignited 

locatInG the new water heater

by a gas water heater’s hot surface igniter or main burner. The resulting 

flashback and fire can cause death or serious burns to anyone in the area 

and property damage. This water heater is equipped with a FV sensor 

for detecting the presence of flammable vapors, see Figure 3. When the 

 

sensor detects those vapors, the unit will shut down and not operate. 

Should this happen, please refer to troubleshooting guide in this manual. 

Even though this water heater is a flammable vapors ignition resistant 

water heater and is designed to reduce the chances of flammable vapors 

being ignited, gasoline and other flammable substances should never 

be stored or used in the same vicinity or area containing a gas water 

heater or other open flame or spark producing appliance.

fIGure 3.

Also, the water heater must be located and/or protected so it is not 

subject to physical damage by a moving vehicle.

This  water  heater  must  not  be  installed  directly  on  carpeting.  

Carpeting must be protected by metal or wood panel beneath the 

appliance extending beyond the full width and depth of the appliance 

by at least 3” (7.6 cm) in any direction, or if the appliance is installed 

in an alcove or closet, the entire floor must be covered by the panel.  

Failure to heed this warning may result in a fire hazard.

Summary of Contents for Power Direct ventedGas SERIES





































Reviews: