background image

 

 

 

 

 

 

 

0312735_ITE_400-1000_EN_V1.0, 2017-09-25

 

15 

 

Maintenance 

 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

4.1  Preparation for 
 

maintenance 

 
 
 
 
 
 
 
 

4.2  Water-side  
 

maintenance 

 

 

4.2.1 

 

Warning 

Maintenance may only be carried out by a competent person. 

 
At each service, the water heater undergoes maintenance on water side. The 
maintenance must be carried out in the following order. 
1.  Preparation for maintenance 
2.  Water-side maintenance 
3.  Finalising maintenance 
 

Note 

Before ordering spare parts, it is important to write down the installation type, water 
heater model and the full serial number of the water heater. These details can be 
found on the rating plate. Only by ordering with this information can you be sure 
receiving the correct spare parts. 

 
 
 
The preparation for maintenance consists of testing and checking if all components 
are still working properly by completing the following steps: 
1.  Test the operation of the overflow valve of the protected cold supply setup. The 

water should discharge 

2.  Check the drainage pipes from the discharge points of all valves and remove any 

scale deposits that may be present. 

3.  Drain the water heater. 
 
 
 
Water-side maintenance consists of descaling and cleaning the tank and checking 
the anodes. 
 
 

Descaling and cleaning the tank

 

Scale and lime build-up prevent effective conduction of the heat to the water. 
Periodic cleaning and descaling prevents build-up of these deposits. This increases 
the service life of the water heater, and also improves the heating process. 
 
Take the rate of scale formation into account when deciding on the service interval. 
Scale formation depends on the local water composition, the water consumption and 
the water temperature setting. A water temperature setting of maximum 60°C is 
recommended for the prevention of excessive scale build-up. 
 
To guarantee a good, watertight seal around the cleaning opening, replace the 
gasket, washers, bolts and, if necessary, the lid with new parts before reassembly. 
Spare parts are obtainable from the supplier/manufacturer. 
 
To simplify descaling and cleaning of the tank, the water heater is equipped with a 
cleaning opening. 
 

 

Summary of Contents for ITE -1000



















Reviews: