manualshive.com logo in svg

A.O. Smith 305, Operation & Installation Manual, Page: 24 / 40

Share
Download
A.O. Smith 305 Operation & Installation Manual Download Page 24

 

24 

305, 505, 705 Indoor Manual 

Listed and Tested Vent Products for the 305 and 505 Models 

Manufacturer Product 

Parts 

Ubbink 

Rolux Vent System  

Heat-Fab 

Saf-T Vent SC system 

Metal-Fab 

Corr/Guard Vent/Air  

Intake System 

Refer to the manufacturer’s technical literature for 
specific part numbers and instructions.   

Listed and Tested Vent Products for the 705 Model 

Manufacturer Product 

Appliance 

Adapter 

Vertical 

Termination 

Horizontal 

Termination 

Horizontal Concentric 

Termination 

Heat-Fab 

Saf-T Vent  

9401AMTK 

5400CI 

9492 

NA 

Z-Flex  

Z-Vent 

2SVSNA04.5 

2SVSRCF4 

2SVSTPX4 

NA 

ProTech Systems 

FasNSeal 

FSAAU4 

FSRC4 

FSBS4 

FSDVPTB04LH 

FSDVWT4 

Metal-Fab Corr/Guard 

4CGOA 4CGSWC 

4CGSWMCM 

4CG7HT90 

4CG7HT 

  

Venting 

Products       

                       

Vent Manufacturer Contact Information for Installation Instructions and Parts Lists: 

Heat-Fab 

Telephone: 800-772-0739 
Fax: 413-863-4803 
E-mail:  

[email protected] 

Web Site:   www.heatfab.com 

Ubbink 

Telephone: 888-928-3719 
500 Tennessee Waltz Parkway 
Ashland City, TN 37015 

Metal-Fab Inc. 

Telephone: 800-835-2830 
 316-943-2351 
Fax:  

316-943-2717 

E-mail:  

[email protected] 

Web Site:   www.metal-fabinc.com 

ProTech Systems, Inc. 

Telephone: 800-766-3473 
 518-463-7284 
Fax: 518-463-5271 
E-mail: [email protected] 
Web Site:  www.protechinfo.com 

Z-Flex 

Telephone: 800-654-5600 
Fax: 888-889-3539 
E-mail: [email protected] 
Web Site:  www.novaflex.com 

Summary of Contents for 305









































Reviews:

No comments