background image

RESIDENTIAL GAS WATER HEATERS

Installation and Operating Manual

1906 

 

 100304526_2000545240       _Rev. 01

KEEP THIS MANUAL IN THE POCKET ON HEATER FOR FUTURE REFERENCE

WHENEVER MAINTENANCE ADJUSTMENT OR SERVICE IS REQUIRED.

POWER DIRECT VENT GAS MODELS

WITH HOT SURFACE IGNITION

NOT FOR USE IN MANUFACTURED (MOBILE) HOMES

• 

For Your Safety

 •

AN  ODORANT IS ADDED TO THE GAS USED

BY THIS WATER HEATER.

Read and understand instruction 
manual and safety messages 
before installing, operating or 
servicing this water heater.
Failure to follow instructions and 
safety messages could result in 
death or serious injury.
Instruction manual must remain 
with water heater.

WARNING

ALL TECHNICAL AND WARRANTY QUESTIONS:

 SHOULD BE DIRECTED TO THE LOCAL DEALER FROM WHOM THE WATER HEATER WAS 

PURCHASED. IF YOU ARE UNSUCCESSFUL, PLEASE CONTACT THE COMPANY LISTED ON THE RATING PLATE ON THE WATER HEATER.

 

SERIES 300, 301 

      

 

 

       

- Do not store or use gasoline or other flam-

mable vapors and liquids in the vicinity of 
this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

  • Do not try to light any appliance.

  • Do not touch any electrical switch; do not 

use any phone in your building.

  • Immediately call your gas supplier from a 

neighbor's phone. Follow the gas sup-
plier's instructions.

  • If you cannot reach your gas supplier, call 

the fire department.

- Installation and service must be performed by 

a qualified installer, service agency or the 
gas supplier.

WARNING: If the information in these instruc-
tions is not followed exactly, a fire or explosion 
may result causing property damage, personal 
injury or death.

Summary of Contents for 300 Series





























































Reviews: