background image

8

P/N 1010751 Rev. G 01/08 

McDonald’s

Multi-purpose steaMer - Mps-250

iNstallatioN (continued)

Multi-Purpose Steamer

Water Pressure 
Regulator Assembly
Kit #7000235
(Optional)

#8 Bracket Screws (3)

Male Quick Disconnect Insert

Figure 3. Connecting Water supply to MPs-250

oPeratioN

General

roCKer sWitCh (PoWer oN/oFF)

When the power is on (Figure 4), the control board 

is activated and a thermostat senses generator tem-

perature.  If generator temperature is below the factory 

preset setpoint, power is applied to the generator until 

setpoint is reached.  The generator is constantly moni-

tored and power is regulated to maintain temperature 

setpoint.

MeNu ButtoNs

When any menu button is pressed and released, power 

is supplied to the solenoid, the solenoid operates and 

water sprays onto the heated steam generator.  The 

water flashes immediately into live steam and shoots 

down onto the product.

One of two operational modes can be used: 

single

 

shot 

or 

timed Cycle

siNGle shot

The 

siNGle shot

 button (Figure 4), is pressed to    

initiate a single timed shot.  The control board applies 

power to the solenoid and a timed “shot” of steam 

occurs.

tiMed CYCle

The desired timed cook cycle (up to 99 minutes, 59 

seconds) is selected by pressing and releasing any of 

the four menu buttons (Figure 4).  The main control 

board applies power to the solenoid at regular intervals 

for the duration of the displayed cycle time.  The dis-

play counts down to zero when the cycle is complete, 

then reverts back to the original programmed cycle 

time and the unit is ready for the next cycle.

iMPortaNt:  Your Multi-Purpose steamer is  

factory programmed for the following on each of  

its four channels except for models 9100336 and 

9100346 (see “exception” on next page).

Channel 1:  6 BuNs

 •  Total Cycle Time (CYC) = 30 seconds [0030]

 

(Range: 1 sec to 99 mins 59 secs)

 •  Shot Interval Time (RATE) = 6 seconds [0006]

 

(Range: 1 sec to 5 mins 59 secs)

 •  Steam Shot Time (SHOT) = 

 0.70 seconds 

[0_70] 

(Range: 0.10 sec to 2.50 secs)

Channel 2:  4 BuNs

 •  Total Cycle Time (CYC) = 20 seconds [0020]

 

(Range: 1 sec to 99 mins 59 secs)

 •  Shot Interval Time (RATE) = 5 seconds [0005]

 

(Range: 1 sec to 5 mins 59 secs)

 •  Steam Shot Time (SHOT) = 

 0.70 seconds 

[0_70] 

(Range: 0.10 sec to 2.50 secs)

Inlet Hose Assy. 0010503 

(See page 20)

Summary of Contents for MPS-250

























Reviews: