background image

Rapid toasteR VCt-250

P/N 00837 Rev. L 03/07 

McDonald’s

daily cleaning

Note:  also refer to ts 019b-1 Card (p/N 1010847).

  .  Turn the Rocker Switch (power ON/OFF) to OFF, 

unplug the toaster and allow it to cool down. 

  2.  Put on heat Resistant Gloves

 and remove the Bun 

Feeder and Bun Chute (Figure 0). Wash them at 

the sink and allow to air dry.

  3.  Remove the Release Sheet (Figure 9) and lay 

it on a clean, flat, dry surface. Spray 

Mcd© 

all-purpose super Concentrate (hCs)

 on a 

clean, dry towel. Wipe the towel firmly across the 

Release Sheet lengthwise over its entire surface. 

Immediately, repeat this procedure with a clean, 

dry towel dampened with 

KaYQUat™ sanitizer 

(hCs)

 solution and allow the Release Sheet to air 

dry.  Turn the Release Sheet over and repeat this 

cleaning procedure on its other side.

  4.  Open the Front (heel/Club side) Conveyor Cover, 

spray 

Mcd© all-purpose super Concentrate 

(hCs)

 on a clean, dry towel and wipe the sur-

face of the Belt Wrap firmly from side to side 

and then top to bottom. Immediately, repeat the 

procedure with a clean, dry towel dampened with 

KaYQUat™ sanitizer (hCs)

 solution. Close the 

Conveyor Cover and repeat this procedure on the 

second, rear (Crown side) Belt Wrap.

Note:  do not remove belt Wrap from unit.

  5.  Plug in the power cord and turn the unit ON, 

count ten (0) seconds for MFG# 920606, count 

thirteen (3) seconds for MFG# 92066. For 

MFG# 920607, 608, 63, 65, 624, & 626 count  

seventeen (7) seconds. Then, turn the unit OFF 

and unplug the power cord. Repeat Step 4 again 

on both Belt Wraps, heat Dampers and the sur-

face of the Inner Conveyor Covers.

Note:  Make sure both Conveyor safety interlock 

switches are activated when the covers are 

installed (figure 10) or conveyors will not rotate.

  6.  Plug the power cord in and turn on the unit, fold 

the Release Sheet in half and place it over the 

Platen. Allow it to be drawn into place and posi-

tioned properly. 

MaiNteNaNCe

WaRNiNG

turn the unit off, disconnect the power source 

and allow the unit to cool down before performing 

any service or maintenance on the unit.

POW

ER

TEMP

DOW

N

TEMP

UP

TEMP

SCAL

E

°C

°F

CAU

TIO

N

figure 10. Removing/installing Release sheet

Bun Feeder

Platen

Bun Feeder Clip

Release Sheet

Bun Chute

Note:  Check the release sheet to make sure it is 

not caught in the conveyor.

  7.  Turn the unit OFF and re-install the Bun Feeder 

and Bun Chute.

  8.  Wipe the entire exterior surface to the toaster with 

a clean, dry towel, dampened with 

KaYQUat™ 

sanitizer (hCs) 

and allow it to air dry.

  9.  verify that the Bun Thickness Compression 

Controls are set properly. Refer to Table .  

Summary of Contents for 9210606





























Reviews: