909 PS120 Instruction Manual Download Page 5

5

4) Power tool use and care
a) Do not force the power tool. Use the correct power 

tool for your application.

 The correct power tool will 

do the job better and safer at the rate for which it was 

designed.

b) Do not use the power tool if the switch does not turn 

it on and off.

 Any power tool that cannot be controlled 

with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or 

the battery pack from the power tool before making 

any adjustments, changing accessories, or storing 

power tools.

 Such preventive safety measures reduce 

the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children 

and do not allow persons unfamiliar with the power 

tool or these instructions to operate the power tool.

 

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or 

binding of moving parts, breakage of parts and any 

other condition that may affect the power tool’s 

operation. If damaged, have the power tool repaired 

before use.

 Many accidents are caused by poorly 

maintained power tools.

f ) Keep cutting tools sharp and clean.

 Properly 

maintained cutting tools with sharp cutting edges are  

less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc. 

in accordance with these instructions, taking into 

account the working conditions and the work to be 

performed.

 Use of the power tool for operations different 

from those intended could result in a hazardous situation.

h) This appliance is not intended for use by persons 

(including children) with reduced physical, sensory 

or mental capabilities, or lack of experience and 

knowledge, 

unless they have been given supervision or 

instruction concerning use of the appliance by a person 

responsible for their safety.

i) Children should be supervised to ensure that they do 

not play with the appliance.

5) Service
a) Have your power tool serviced by a qualified repair 

person using only identical replacement parts.

 This 

will ensure that the safety of the power tool is maintained.

b) If the supply cord is damaged, it must be replaced by 

the manufacturer,

 its service agent or similarly qualified 

persons in order to avoid a hazard.

Additional safety rules  

for wetstone sharpeners

Note. 

It is recommended to use in conjunction with this 

appliance a Residual Current Device (RCD) of rating not 

exceeding 30mA.

  Always remove the plug from the mains socket before 

making any adjustments or maintenance, including 

changing the wheel.

  Always turn the sharpener off when it is not in use and 

never leave it unattended without first switching off and 

removing the power plug. Never leave the sharpener  

until the wheels have come to a complete stop.

  Make sure that any replacement wheel is rated at 120rpm 

or higher. 

  Do not let anyone under 18 years operate this tool.

  Rags, cloths, cord, string and the like should never be left 

around the work area.

  If you are interrupted when operating the tool, complete 

the process and switch off before looking up.

  Periodically check that all nuts, bolts and other fixings are 

properly tightened.

  Do not use a wheel that has received a blow, especially 

to the side of the wheel.

  Replace a cracked or suspect wheel.

  Always allow a new wheel to run for a few minutes at full 

speed before using it. Stand to one side at start up.

Summary of Contents for PS120
















Reviews: