80% Arms FST-1 Operator'S Manual Download Page 12

10-0

7

-20

 

(REV. 0.9

7

)

OPERATOR’S MANUAL

HIGH-SPEED PRECIS

I

ON COMPACT ROUTER

80 PERCENT ARMS

12282 Monarch Street

Garden Grove, CA 92841, USA

1-949-354-2767 

  www.80PercentArms.com

Copyright© 2020 80 Percent Arms

80  PERCENT  ARMS  LIMITED  ONE  YEAR  WARRANTY  -  Warranty  Policy

Every 80 Percent Arms tool is thoroughly inspected and tested before leaving 

the  factory.  It  is  warranted  to  be  free  of  defects  from  workmanship  and 

materials  for  the  period  of  ONE  YEAR  from  the  date  of  original  purchase. 

Should any trouble develop during this one year period, return the complete 

tool,  freight  prepaid,  to  80  Percent  Arms.  If  inspection  shows  the  trouble  is 

caused by defective workmanship or material, 80 Percent Arms will repair (or 

at our option, replace) without charge.

This  Warranty  does  not  apply  when:

Repairs  are  required  because  of  normal  wear  and  tear

The  tool  has  been  abused,  misused  or  improperly  maintained

Modifications  have  been  made  to  the  tool

IN  NO  EVENT  SHALL  80  PERCENT  ARMS  BE  LIABLE  FOR  ANY  INDIRECT, 

INCIDENTAL  OR  CONSEQUENTIAL  DAMAGES  FROM  THE  SALE  OR  USE  OF 

THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE 

TERM OF THIS WARRANTY.

80 PERCENT ARMS DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, 

INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS 

FOR  A  SPECIFIC  PURPOSE,"  AFTER  THE  ONE  YEAR  TERM  OF  THIS 

WARRANTY.

This  Warranty  gives  you  specific  legal  rights,  and  you  may  also  have  other 

rights which vary from state to state. Some states do not allow the exclusion 

or limitation of incidental or consequential damages, so the above limitation or 

exclusion may not apply to you. Some states do not allow limitation on how 

long an implied warranty lasts, so the above limitation may not apply to you.

For replacement parts or service, 

c

ontact 80 Percent Arms. For the location of 

our service center nearest to you, please call (949) 354-2767 or visit us online 

at www.80PercentArms.com.

WARRANTY

1

2

Summary of Contents for FST-1













Reviews: