background image

Pag 4 | 13   

www.6tlengineering.com

   24/06/2022   YAV90059   

 
 

3. 

DESCRIPTION 

 

The YAV90059 module is controlled through CAN Bus and features104 DPST relays forming 
two 4-poles, 2-Poles or 1-Pole Multi-configuration Multiplexers. 

The configuration of the multiplexer is selected by a software command. The 

‘mode’ is an 

analog output Phi6 function, where the input parameter can be 1 to 13. The modes available are 
the following: 

1.  8 x(1x16) 

 8 banks of 16 individual outputs. This is the default mode. 

2.  4x(1x32) 

 4 banks of 32 individual outputs. 

3.  1x(1x64)  +  2x(1x32) 

  1  bank  of  64  individual  outputs  and  2  banks  of  32  individual 

outputs. 

4.  1x(1x96) + 1x(1x32) 

 1 bank of 96 individual outputs and 1 bank of 32 individual outputs. 

5.  2(1x64) 

 2 banks of 64 individual outputs. 

6.  1(1x128) 

 1 bank of 128 individual outputs. 

7.  8 x(2x8) 

 8 banks of 8 double outputs. 

8.  4 x(2x16) 

 4 banks of 16 double outputs. 

9.  1 x(2x32) + 2x(2x16) 

 1 bank of 32 double outputs and 2 banks of 16 double outputs. 

10. 1 x(2x48) + 1x(2x16) 

 1 bank of 48 double outputs and 1 bank of 16 double outputs. 

11. 2 x(2x32) 

 2 banks of 32 double outputs. 

12. 1 x(2x64) 

 1 bank of 64 double outputs. 

13. 4x(4x8) 

 4 banks of 8 quadruple outputs (2 locked double outputs). 

 

 

 

Summary of Contents for YAV90059














Reviews: