background image

Hacousto Holland bv 

Industrieweg 87 

2651BC  Berkel & Rodenrijs 

 

4E-CMT installation and user guide 

Author: 

DD 

 

 

 

Page 8 of 13 

  

 

 

Device ID 

The microphone station needs an ID setting in order to be properly recognized in the network and operate. 
If the device ID is duplicated or set to a wrong value, the device will not receive the correct configuration 

settings from the main unit. In this case the remote station will be stuck in its boot sequence and remain 

non-operational. 
Device ID is set by means of two rotary switches, which define the two-digit hexadecimal value of the ID. 
In order to check or set the Device ID, you must access the rotary switches on the back side of the unit: 

1.

 

Remove the steel plate covering back of the console. 

2.

 

Identify high-significant and low-significant rotary switches. The Device ID is a combination [HI LO] 

of those two digits. 

3.

 

Make sure the ID value exists in your configuration settings, relates to the right device type and is 

not duplicated to another device. Allowed values: 01-FE 

4.

 

Set the Device ID value according to the configuration settings of the 4EVAC system.  

5.

 

Plug-in the L-Net cable connecting the station with the 4EVAC main unit. 

6.

 

Observe the boot sequence which should see the unit automatically entering normal operating 

mode afterwards. 

7.

 

Assemble the back plate (and optionally the rubber feet). 

 

 

4E-CMT bottom view: Device ID setting 

 

 

HIGH 
LOW 

Summary of Contents for 4E-CMT














Reviews: