3TO BRACE Set Of Instructions Download Page 20

 

 

20

6.2 General treatment information 

 

 Any inflammatory areas must be treated. 

 

  Once  the  nail  has  adapted  the  form  of  the  brace,  the  brace  may 

become loose and may fall off. If that happens, it is recommended to 
remove  the  brace  and  re-adjust  it  proximally  to  the  previous 
position. 

  

  The  tension  caused  by  the  brace  is  helpful  in  case  of  an 

onychomycosis (ringworm of the nail), since it provides better access 
to the areas affected that can be treated more easily. 

 

  Ask  the  patient  to  show  up  again  for  control  depending  on  the 

severity of the condition: 

- after 1-3 days in case of a severe condition 
- after 3-6 days in case of mild condition 

 

 Please provide the patient with any relevant information 

-  Provide  information  about  the  method  of  action  and  any  possible 
undesired side effects of the brace 

- Try to explore the causes for ingrown nails together with the 

patient and come up with a proposal how to manage the problem in 
the future. 

 

These  instructions  should  be  used  in  order  to  avoid  any 
accidents  and  injuries  and  all  notes  and  rules  regarding 
disinfection must be observed!

 

 

__________________________________________________ 

 

3TO GmbH 

Birkenstraße 8 
D-82041 Deisenhofen 

 

Tel.:   +49 89 4520833-0 
Fax:   +49 89 4520833-99 
[email protected] 
www.3to-spange.com 

 

Summary of Contents for BRACE





















Reviews: