【
Communication Connector
】
PD101G Series
provide 1*10/100/1000M POE ports,
1*10/100/1000M ports.
10/100/1000BaseT(X) Ethernet port
10Base-T/100Base-TX/1000
Base-TX
Ethernet port use in front panel, It is RJ45 port, the PIN
define of RJ45 is as follows: connection adopt UTP or
STP, the distance is no more than 100m, 1000Mbps use
cat5e, 100Mbps use cat5, 10Mbps use cat3,4, 5.
RJ45 port support MDI/MDI-X self-adaption. In
(MDI), PIN1, 2, 3, 4, 5, 6, 7, 8 connect corresponding, in
(MDI-X) PIN1→3, 2→6, 3→1, 6→2, 4→7, 5→8, 7→4,
8→5. In MDI/MDI-X, 1000 Base-TX PIN define is as
follows:
Note
：“
TX
±”
Transmit Data
±，“
RX
±”
Receive Data
±，“—”
Not Use
。
MDI (straight-through cable):
MDI-X (Cross over cable)
MDI/MDI-X auto connection makes PD101G series easy to
use for customers without considering the type of network cable.
【
LED Indicator
】
PD101G Series indictor light on the front panel. the function
of each LED is described in the table as below.
System Indication LED
LED
State
Description
PWR
ON
Power is being supplied to
power input PWR input
OFF
Power is not being supplied
to power input PWR input
【
Installation
】
Operation Cautions
1)
Don’t stock the device in damp environment or near
water, to avoid water or moisture penetrating into the
inner device.
2)
Don’t put the device on a unstable box or desk, the
device will get damaged from falling.
3)
Please check and make sure the operation voltage is
meet the voltage standard marked on the device surface
before the next steps.
4)
Please use a grounded three-hole power socket in the
rack or desk mounting, to mitigate damage caused by
electro-static discharge or lightning stoke.
5)
Keep the device far from heat sources, strong power
radio transmitters and radar transmitters.
6)
Similar with other electrical products, the semiconductor
chip in device will get damaged when open and shut off
the power frequently. Please restart the device 3~5
seconds(or longer) after the power is shut off.
7)
Please pull out the power plug before cleaning the
device. Don’t wipe the device with wet cloth or clean the
device with liquid.
8)
To guarantee a long operation life, the device can only
be used in indoor and in ventilated & dry environment.
And to get a good heat dissipation, please reserve a
space over 10CM around the device.
POESplitter Operation Instruction
1)
Connect “ Power+Data”port on POE splitter with a
RJ45 cable, which connected with far-end POE switch
or POE injector on the other end. When one of the three
voltage LED indicator(5V/9V/12V) is on, the
connection is successful.
2)
Please choose right voltage state according to your POE
PDs, the default voltage state is 5V, you can slide the
switch to change to 9V or 12V.
3)
Connect the provided DC power cord to the“Power
OUT” port on the POE splitter, and connect the other
end to the POE PDs with right plugs( 4 types universal
plugs for your option).
4)
Please connect one end of provided RJ 45 cable to the
“Data OUT” port of POE splitter, and connect the other
end to the data in port of POE PDs.
PIN
MDI
MDI-X
1
BI_DA+/TX+
BI_DB+/RX+
2
BI_DA-/TX-
BI_DB-/RX-
3
BI_DB+/RX+
BI_DA+/TX+
4
BI_DC+/
—
BI_DD+/
—
5
BI_DC-/
—
BI_DD-/
—
6
BI_DB-/RX-
BI_DA-/TX-
7
BI_DD+/
—
BI_DC+/
—
8
BI_DD-/
—
BI_DC-/
—
1
8
