3onedata MES600 Series User Manual Download Page 63

Page: 63 / 76

Industrial Ethernet Switch User Manual

3onedata proprietary and confidential

Basic settings

13.1 Log information

The device provides system log for user's reference of troubles. When enabling this

function, the following events will be recorded:

The all information, boot information, handing information, linkage information.

13.2 SNTP

NTP (Network Time Protocol) is a protocol and software implementation for

synchronizing the clocks of computer systems over packet-switched data network. It

provides coordinated universal time including scheduled adjustments. No information

about time zones or daylight saving time is transmitted; this information is outside its

scope and it must be obtained separately.

Summary of Contents for MES600 Series













































































Search results

Summary of Contents for MES600 Series

Reviews:

Related manuals for MES600 Series

Brands by name

Popular brands

3onedata MES600 Series, User Manual

Search results

Summary of Contents for MES600 Series

Reviews:

Related manuals for MES600 Series

Brands by name

Popular brands