- 2 -
8.
Relay alarm indicator
9.
System running indicator
10.
PoE port Link/ACT indicator
11.
10/100M Base-T(x) PoE port
12.
Ethernet port Link/ACT indicator
13.
Gigabit SFP port of the combo port
14.
Gigabit copper port of the combo port
15.
10/100M Base-T(x) port
【
Dimension
】
The series of products size is same, and the type of the Ethernet
interface is different. Unit (mm)
【
Power supply input
】
The product top panel provided 4 bit power supply input terminal
block, support DC input. DC power supply input supported
redundancy function, provided PWR1 and PWR2 power input,
can use for single, and can connect 2 separately power supply
system, use 1 pair terminal block connect the device at the same
time. If one of the power systems broke, the device can work
un-interruptible. Built-in overcorrect protection, Reverse
connection protection. Voltage input range is 48VDC (terminal
block defined as: V1-
、
V1+
、
V2-
、
V2+). The power supports
reverse connection protection.
【
Relay connection
】
Relay access terminals in the top panel of the device. Between the
two terminal relay, as an open circuit state in normal non alarm
state, when there is power alarm information to the closed state.
The two terminal block connector are used to detect power failure
and network anomaly. The two wires attached to the Fault
contacts form a closed circuit when the device port connection
disconnect or has lost power supply from one of the DC power
inputs. The user can connect the relay to the lamp indicate or
buzzer alarm to remind the relevant staff.
【
Console port
】
This series product provided 1pcs procedure test port based in
serial port. It adopts RJ45 interface, located in top panel, can
configure related command through RJ45 to DB9 female cable.
【
DIP Switch
】
Top panel provided 4 bits DIP switch to do function configure
(ON to enable effective), 1 is data upgrade testing (8POE) /
reserved (4POE). 2 is recovery default factory. 3 is for upgrade. 4
is reserved. Please power off and power on when you change the
status of DIP switch.
【
Communication connector
】
10/100/1000BaseT(X) Ethernet port
The pinout of RJ45 port display as below, connect by UTP or STP.
The connect distance is no more than 100m. 1000Mbps is used
120Ω of UTP 5e; 100Mbps is used 120Ω of UTP 5; 10Mb
ps is
used 120Ω of UTP 3, 4, 5.
RJ 45 port support automatic MDI/MDI-X operation. That can
connect the PC, Server, Converter and HUB. Pin 1, 2, 3, 4, 5, 6, 7,
8 Corresponding connections in MDI. 1→3, 2→6, 3→1, 4→7,
5→8, 6→2, 7→4, 8→5, are used as cross w
iring in the MDI-X
port of Converter and HUB. In MDI/MDI-X, 100/1000Base-TX
PIN defines is as follows:
PIN
MDI
MDI-X
1
BI_DA+/TX+ BI_DB+/RX+
2
BI_DA-/TX-
BI_DB-/RX-
3
BI_DB+/RX+ BI_DA+/TX+
4
BI_DC+/—
BI_DD+/—
5
BI_DC-/—
BI_DD-/—
6
BI_DB-/RX-
BI_DA-/TX-
7
BI_DD+/—
BI_DC+/—
8
BI_DD-/—
BI_DC-/—
Note: 10Base-T/100Base-TX, “TX±”transmit data±, “RX±”receive data±,
“—”not use.
10/100Base-T(X) MDI (straight-through cable)
