Power ON operation: First insert the power supply
terminal block into the device power supply interface,
and then plug the power supply plug contact and power
on.
Power OFF operation: First, remove the power plug,
and then remove the wiring section of terminal block.
Please pay attention to the above operation sequence.
【
Reset Button Setting
】
This device provides 1 reset button, press the button
for 1-2S then release it to reboot the device; press the
button for 5S then release it to restore factory defaults.
【
Checking LED Indicator
】
The device provides LED indicators to monitor the device
working status with a comprehensive simplified
troubleshooting; the function of each LED is described in the
table as below:
LED
Indicate
Description
WIFI
ON
WIFI is running normally
OFF
WIFI is running abnormally
or closed
RUN
ON
The device is powered on
or the device is abnormal.
OFF
The device is powered off
or the device is abnormal.
Blinking
The device is running
normally
PWR
ON
PWR is connected and
running normally
OFF
PWR is disconnected and
running abnormally
Bridge
OFF
No bridging is established
ON
The strength of bridging
signal is 70~100dBm
1 time/1s Blinking
The strength of bridging
signal is 30~70dBm
1 time/2s Blinking
The strength of bridging
signal is 1~30dBm
【
Logging in to WEB Interface
】
This device supports WEB management and configuration.
Computer can access the device via LAN. The way of logging
in to device’s configuration interface via IE browser is shown
as below:
Step 1
Configure the IP addresses of computer and the
device to the same network segment, and the
network between them can be mutually accessed
Step 2
Enter device’s IP address in the address bar of the
computer browser.
Step 3
Enter device’s user name and password in the
login window as shown below.
Step 4
Click “Login” button to login to the WEB interface of
the device.
Note:
The default IP address of the device is “192.168.1.254”.
The default user name and password of the device is
“admin”.
If the user name or password is lost, user can restore it
to factory settings via restore button or management
software; all modified configurations will be cleared
after restoring to factory settings, so please backup
configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【
Specification
】
Standard
Standard
IEEE802.3
、
IEEE802.3u
、
IEEE802.11b/g/n
、
IEEE802.11i
、
IEEE802.11r
Panel
Copper Port
5 10/100Base-T(X) RJ45
ports: 4 LAN + 1 WAN.
Antenna pedestal
2 WIFI IPEX-1 generation
antenna pedestals, RP-SMA-K
type (Female), support 1.5kV
isolation protection
Indicator
Signal indicator, Running
indicator, Power supply
indicator, 2.4G wireless
indicator
WIFI Transmission Rate
802.11n
6.5~300Mbps
802.11b
11/5.5/2/1Mbps
802.11g
54/48/36/24/18/12/9/6Mbps
WIFI RF
Channel
2.412GHz~2.4835GHz
RF power output
23dBm
Modulation scheme
DBPSK, DQPSK, CCK,
OFDM, 16-QAM, 64-QAM
WIFI Receiving
Sensitivity
802.11n_HT40
-82dBm@MCS0
、
-64dBm@MCS7
802.11n_HT20
-85dBm@MCS0
、
-67dBm@MCS7
802.11g
-91dBm@6Mbps
、
-72dBm@54Mbps
802.11b
-93dBm@1Mbps
、
-87dBm@11Mbps
WIFI Transmission
