background image

4

Limitations of Use

1.  Do not wear this respirator to enter areas where:

a.  Atmospheres are oxygen deficient. 

b.  Contaminant concentrations are unknown.

c.  Contaminant concentrations are Immediately Dangerous to Life or Health (IDLH).

d.  Contaminant concentrations exceed the maximum use concentration (MUC) as determined using 

the Assigned Protection Factor (APF) for the specific respirator system or the APF mandated by 

specific government standards, whichever is lower. See “APF” section of these 

User Instructions

Respirator Program Management  

Occupational use of respirators must be in compliance with applicable health and safety standards. By 

law, US employers must establish a written respiratory protection program meeting the requirements of 

the OSHA Respiratory Protection Standard 29 CFR 1910.134 and any applicable OSHA substance specific 

standards. For additional information on this standard contact OSHA at www.OSHA.gov. In Canada, CSA 

standard Z94.4 requirements must be met and/or requirements of the applicable jurisdiction, as appropriate. 

The major sections of 1910.134 are listed here for reference. Consult an industrial hygienist or call 3M 

Technical Service with questions concerning applicability of these products to your job requirements

.

Major Sections of OSHA 29 CFR 1910.134

Section 

Description

A

Permissible Practice

B

Definitions

C

Respiratory Protection Program 

D

Selection of Respirators

E

Medical Evaluation

F

Fit Testing

G

Use of Respirators

H

Maintenance and Care of Respirators

I

Breathing Air Quality and Use

J

Identification of Cartridges, Filters, and Canisters

K

Training and Information

L

Program Evaluation

M

Recordkeeping

NIOSH - Approval, Cautions, & Limitations 

These products are one component of a NIOSH approved respiratory protection system. Refer to the 

User 

Instructions

 and/or the NIOSH Approval Label provided with the 3M™ Supplied Air (SA) or Powered Air 

Purifying (PAPR) Blower Unit for approved configurations and applicable NIOSH Cautions and Limitations. 

 

Additional Certifications

W

 WARNING

1.  These products meet the requirements of certain industrial eyewear standards and with some 

models, certain industrial head protection standards. They do not provide complete head, eye, 

and face protection from severe impact and penetration and are not a substitute for good safety 

practices and engineering controls. 

Misuse may result in serious injury or death

. For proper 

use, see supervisor, refer to the product 

User Instructions

 or contact 3M Technical Service.

2.  When exposed to eye and face hazards, wear additional eye and/or face protectors appropriate to 

the hazard. ANSI Z87.1-2010, incorporated by reference in the OSHA Eye and Face Standard 29 

CFR 1910.133, suggests safety spectacles or goggles should be worn in conjunction with loose 

fitting respirators if the visor can be raised from the normal position during use. 

Failure to do so 

may result in serious injury.

[email protected]      |      http://www.bestmaterials.com      |      1-800-474-7570

Distributed by Best Materials® LLC

Summary of Contents for Versaflo M Series




























Reviews: