manualshive.com logo in svg

3M UniPresser 3M710, Instructions Manual

Share
Download
3M UniPresser 3M710 Instructions Manual Download Page 16

 DOCUMENT

 OBSOLETE

Telecom Access Division
3M Telecommunications

6801 River Place Blvd.
Austin, TX 78726-9000
www.3MTelecommunications.com

Litho in USA.

© 3M 2002 78-8125-3042-2-B

IMPORTANT NOTICE

Before using this product, you must evaluate it and determine if it is suitable for your intended application.  You assume all risks and
liability associated with such use. 

Warranty; Limited Remedy; Limited Liability.   This product will be free from defects in material and manufacture as of the date of
purchase.  3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated 
above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M 
product.  Except where prohibited by law, 3M will not be liable for any loss or damage arising from this 3M product, whether
direct, indirect, special, incidental or consequential regardless of the legal theory asserted.

3M is a registered trademark of 3M Company.

Summary of Contents for UniPresser 3M710

















Reviews:

No comments

Brands by name

Popular brands

Load more brands