3M MG-1000 Manual Download Page 36 | Manualshive

Page: 36 / 90

background image

26 • Ch. 3 Burster Mechanism

75-0302-1450-8, Version 1

SST Transport and Burster Mechanism Manual

Reviewing the Parker

The Parker parks, or holds, tickets for a short period of time so that the SST Transport can process
magnetic stripe vouchers, credit cards, Value Cards, or debit cards. You may find a Parker in the
SST Ticket Validator, the Automatic Pay Station, or the SST Exit Verifier. Figure 3.5 illustrates the
Parker.

Installing the Burster/Parker

To install the Burster/Parker on the SST Transport, complete the following steps:

1. Turn off power to the SST Transport.

Warning! Do not hang the Burster/Parker on the SST Transport when the CPU has power.

This will damage the Burster/Parker. Do not attempt to connect or disconnect

ribbon cables when the power is on. This may cause damage to components.

2. Open the securing knob on the side of the Burster by turning it counterclockwise. Figure

3.6 illustrates the location of the securing knob.

Figure 3.5

Parker

Parker Motor

Motor Holder

Securing Knob

«
...
34
35
36
37
38
...
»

Summary of Contents for MG-1000



























































































Reviews:

No comments

Related manuals for MG-1000

Brand: Keithley Pages: 97

Brand: Happ Pages: 52

Brand: Hansen Pages: 4

HomeTec Pro CFF3000

Brand: Abus Pages: 13

Brand: NAVITAS Pages: 7

Brand: Abus Pages: 2

Brand: BADODOSECURITY Pages: 8

Brand: Danfoss Pages: 85

VLT Decentral FCD 300

Brand: Danfoss Pages: 112

Brand: Danfoss Pages: 4

VLT 6000 series

Brand: Danfoss Pages: 27

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 20

ADAP-KOOL AK-PC 781

Brand: Danfoss Pages: 14

Brand: Danfoss Pages: 12

vlt soft starter mcd 500

Brand: Danfoss Pages: 96

Brand: Habegger Pages: 2

Brand: Jedia Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands