3M MG-1000 Manual Download Page 13 | Manualshive

Page: 13 / 90

background image

SST Transport and Burster Mechanism Manual

75-0302-1450-8, Version 1

Ch. 1 Getting Started • 3

Overview of the Burster Mechanism

The Burster splits tickets at their perforations so that the SST Transport can encode and print the
tickets. There are two kinds of Bursters: the Single Infeed Burster and the Dual Infeed Burster. The
Single Infeed Ticket Burster is the standard ticket bursting mechanism included with all SST
Ticket Spitters. The Dual Infeed Ticket Burster is an optional product. For additional information
on the Burster Mechanism, please refer to

Chapter 3: Burster Mechanism

Overview of the Parker

The Parker parks, or holds, tickets for a short period of time so that the SST Transport can process

magnetic stripe vouchers, credit cards, Value Cards, or Debit Cards. You may find a Parker in the

SST Ticket Validator, the Automatic Pay Station, or the SST Exit Verifier. For additional informa-

tion on the Parker, please refer to

Chapter 3: Burster Mechanism

.

Figure 1.2

Interior of Automatic Pay Station

SST Transport

Inside Door

Interior

Ticket Throat for SST Transport

«
...
11
12
13
14
15
...
»

Summary of Contents for MG-1000



























































































Reviews:

No comments

Related manuals for MG-1000

Brand: Samson Pages: 92

Brand: Jafar Pages: 10

Brand: B&R Industries Pages: 89

vlt soft starter mcd 500

Brand: Danfoss Pages: 95

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 33

Brand: Danfoss Pages: 59

Brand: Danfoss Pages: 16

VLT AQUA Drive FC 200

Brand: Danfoss Pages: 91

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 100

Brand: Danfoss Pages: 82

Brand: Danfoss Pages: 18

Brand: Danfoss Pages: 12

OPTYMA Plus OP-LPQM

Brand: Danfoss Pages: 8

Brand: UCS Pages: 4

Brand: IFM Pages: 49

Brand: IFM Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands