3M Liqui-Cel EXF-8x20 Series Assembly And Disassembly Instructions Download Page 12

LC-1094 

Rev. 04/2021 

3M.com/Liqui-Cel

Technical Information:

 The technical information, guidance, and other statements contained in this document or otherwise provided by 3M are based upon records, tests, or 

experience that 3M believes to be reliable, but the accuracy, completeness, and representative nature of such information is not guaranteed. Such information is intended for 

people with knowledge and technical skills sufficient to assess and apply their own informed judgment to the information. No license under any 3M or third party intellectual 

property rights is granted or implied with this information.

Product Selection and Use:

 Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance of a 3M product in a 

particular application. As a result, customer is solely responsible for evaluating the product and determining whether it is appropriate and suitable for customer’s application, 

including conducting a workplace hazard assessment and reviewing all applicable regulations and standards (e.g., OSHA, ANSI, etc.). Failure to properly evaluate, select, and 

use a 3M product and appropriate safety products, or to meet all applicable safety regulations, may result in injury, sickness, death, and/or harm to property.

Warranty, Limited Remedy, and Disclaimer:

 Unless a different warranty is specifically stated on the applicable 3M product packaging or product literature (in which case 

such warranty governs), 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER 

WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, 

FITNESS FOR A PARTICULAR PURPOSE, OR ARISING OUT OF A COURSE OF DEALING, CUSTOM, OR USAGE OF TRADE. If a 3M product does not conform to this 

warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price.

Limitation of Liability:

 Except for the limited remedy stated above, and except to the extent prohibited by law, 3M will not be liable for any loss or damage arising from or 

related to the 3M product, whether direct, indirect, special, incidental, or consequential (including, but not limited to, lost profits or business opportunity), regardless of the 

legal or equitable theory asserted, including, but not limited to, warranty, contract, negligence, or strict liability.

3M and Liqui-Cel are trademarks of 3M Company. All other trademarks are the property of their respective owners. © 2021 3M Company. All rights reserved.

3M Deutschland GmbH 

3M Separation and Purification 

Sciences Division

 

Öhder Straße 28 

42289 Wuppertal Germany 

Phone: +49 202 6099 - 0

3M Company  

3M Separation and Purification 

Sciences Division

 

13840 South Lakes Drive 

Charlotte, North Carolina 28273 

USA 

Phone: +1 980 859 5400

Summary of Contents for Liqui-Cel EXF-8x20 Series













Reviews: