manualshive.com logo in svg

3M HEADSET C1060, Installation Instructions Manual

Share
Download
3M HEADSET C1060 Installation Instructions Manual Download Page 3

 

 

i

Table of Contents 

Typical Single Lane Installation...................................................................................................................... 1 

Battery Charger ............................................................................................................................................... 2 

Speaker and Microphone Assemblies.............................................................................................................. 3 

Standard Systems ...................................................................................................................................... 3 

Duplex Systems ........................................................................................................................................ 3 

Base Station ..................................................................................................................................................... 3 

Programming Station....................................................................................................................................... 4 

Connecting the Base Station Directly to Components .................................................................................... 5 

Connecting the Base Station to Components Using the Optional Interconnect Module................................. 

6 

Connecting the Auxiliary Intercom (Optional) ............................................................................................... 8 

Dual Lane System Installation......................................................................................................................... 9 

Cross Lane System Installation ....................................................................................................................... 10 

Installation................................................................................................................................................. 11 

Wiring the System .............................................................................................................................. 11 

Programming the Headsets for Cross-Lane Operation ....................................................................... 

11 

Operation................................................................................................................................................... 12 

System Configurations and Function Jumper Settings.................................................................................... 14 

Standard Operation – Single Lane System (One Base Station) ................................................................ 

14 

Standard Operation – Dual Lane System (Two Base Stations) ................................................................ 

14 

Duplex Operation – Single Lane System (One Base Station)................................................................... 

15 

Duplex Operation – Dual Lane System (Two Base Stations)................................................................... 

15 

Channel Selection ............................................................................................................................................ 16 

Setting Audio Levels ....................................................................................................................................... 17 

Duplex Systems Only ............................................................................................................................... 18 

Duplex 

and 

Standard Systems .................................................................................................................. 18 

Alert Tone Level ....................................................................................................................................... 18 

Monitor Speaker Volume Levels........................................................................................................ 19 

Standard Systems Only ............................................................................................................................. 19 

Listen Level (Menu Sign Microphone Sensitivity) ............................................................................ 

19 

Menu Sign Talk Volume Level .......................................................................................................... 20 

Summary of Contents for HEADSET C1060






























Reviews:

No comments

Brands by name

Popular brands

Load more brands