manualshive.com logo in svg

3M GMI PS200-LMP, Operation & Maintenance Manual, Page: 39 / 46

Share
Download
3M GMI PS200-LMP Operation & Maintenance Manual Download Page 39

64220, Rev. 1/April 2019

3M™ GMI™ PS200-LMP AUTO BUMP/CALIBRATION STATION

USB MEMORY STICK CONTENTS

B-1

APPENDIX B. USB MEMORY STICK CONTENTS

B.1. Accessing the Memory Stick Contents

1. The typical contents of the USB memory stick are illustrated in 

Figure B-1:

 

USB Memory Stick Con-

tents

.

Figure B-1:  USB Memory Stick Contents

• Upload Folder: 

Contains ABC configuration files. DO NOT EDIT.

• TestResults Folder:

Contains the test results (as xml files) generated by the ABC. These files are used to create the 

calibration or bump test certificates. DO NOT EDIT. 

• PS200Settings Folder:

Contains ABC system file. DO NOT EDIT.

• Generated Certificates Folder:

Contains all the calibration or bump test certificates (as html files). This folder also contains files 

for logos that appear on the certificates.

• Autorun.inf:

System file. DO NOT EDIT.

• PS200-LMP Settings.exe:

Application that is used to reconfigure the ABC’s operation and extract calibration and bump test 

results from the ABC for viewing and printing.

• ABC Quick Op Guide.pdf:

A pdf file of the supplied illustrated guide on using the ABC.

• ABC Operators Manual.pdf

A pdf file of the ABC Operation & Maintenance Manual (this document).

Summary of Contents for GMI PS200-LMP















































Reviews:

No comments