3M Digital Media System 700P Series Product Safety Manual Download Page 8

8

Introduction

3M

 Digital Media System 700P

© 3M 2007. All Rights Reserved.

ENGLISH

D

 CAUTION

• To reduce the risk associated with intense visible light:

- Avoid looking directly into the projector lens while the lamp is on.

• To reduce the risk associated with impact of a falling projector:

- Use only the 3M brand wall/ceiling mounting hardware kit if wall or ceiling mounting is desired.
- Installation of the 3M wall/ceiling kit must only be performed by qualified personnel.
- Adhere strictly to the proper installation procedure as outlined in the installation instructions 

when installing  the 3M wall/ceiling kit.

- Always operate the unit on a flat, sturdy, and horizontal surface.

• To reduce the risk associated with explosion, and/or chemicals from leaking battery:

- Use only with battery type AAA.
- Orient the battery’s plus (+) and minus (-) terminals according to the markings found on the 

remote control.

- Do not leave the battery in the remote for an extended period of time.
- Do not heat, disassemble, short, recharge, or expose the batteries to fire or high temperature
- Do not carry batteries loose in your pocket or purse.
- Avoid eye and skin contact in the event that battery would leak.
- Do not mix used and new batteries.

• To reduce the risk associated with tripping, and/or impact:

- Position the power cord and data cable so that they can not be tripped over.

• To reduce the risk associated with environmental contamination due to battery chemicals:

- Dispose of exhausted batteries in accordance with applicable federal, state and local regulations.

INTENDED USE

Before operating the machine, please read the entire manual thoroughly. The 3M

 Digital Media System 700P 

was designed, built and tested for use indoors, using 3M

 brand lamps, 3M

 brand ceiling mount hardware 

and nominal local voltages. The use of other replacement lamps, outdoor operation or different voltages has not 
been tested and could damage the projector or peripheral equipment and/or create a potentially unsafe operating 
condition.

SAVE THESE  INSTRUCTIONS

The information contained in this manual will help you operate and maintain your 3M Digital Media System 
700P Series.

Trademarks

The 3M logo and 3M are registered trademarks of 3M Company. Vikuiti is a trademark of 3M Company.

Digital Light Processing is a trademark or registered trademark of Texas Instruments.

Summary of Contents for Digital Media System 700P Series

















Reviews: