3M DBI-SALA Rollgliss 3303015 User Instruction Manual Download Page 1

DESCRIPTION:

The Rollgliss™ High Speed 200 foot Emergency Descent Devices with Auto-Retract are comprised of a Wire Rope Lifeline 

housed in a cast aluminum enclosure. An internal brake controls sloped descent speed of a single user attached to a manual 

brake trolley at the end of the lifeline.

Figure 1 - 200 Ft (61m) Emergency Sloped Descent Device Models

Descent Device Model

Brake Trolley Model

With Yellow Zinc Plated Snap 

Hook, included with 3303015.

2103144

With Stainless Steel Snap Hook, 

included with 3303016.

2103145

Galvanized

3303015

Stainless Steel 3303016

Rollgliss

®

200 Ft Emergency Sloped Descent Device

High Speed with Auto-Retract

User Instruction Manual

This manual is intended to be used as part of an employee training program as required by OSHA. When used and 

maintained in accordance with the manufacturer’s instructions, this product helps provide the method of emergency 

escape when working at height, as referenced by OSHA and industry guidelines including API RP 54 6.12.

Form: 5903739  Rev: F

© 3M 2023

Summary of Contents for DBI-SALA Rollgliss 3303015













Reviews: