3M DBI SALA 8518581 User Instruction Manual Download Page 4

4

• 

 

The worker climbing the ladder is wearing a full body harness

and the winch line is connected to the dorsal (back) D-ring of

the harness.

• 

 

The winch operator is trained and competent in the operation

of the winch.

• 

 

No slack line is allowed to develop when the worker moves

up or down the ladder.

• 

 

DBI-SALA recommends, for the series winches only, that an

energy absorbing lanyard be connected between the harness

dorsal D-ring and the winch line.

1.3 LIMITATIONS: 

The following application limitations must be 

considered before using this product. Failure to observe product 

limitations could result in serious injury or death.

A. INSTALLATION:

 The winch must be installed in accordance 

with the requirements stated in section 3.4 of this manual.

B. CAPACITY: 

The maximum working load for this product is 

one person with a combined maximum weight (including tools, 

clothes, and equipment) of 450 lbs. (204 kg).

C.  PERSONAL FALL ARREST SYSTEMS: 

Personal fall arrest 

systems used with the Digital Winch must meet applicable 

state and federal regulations and the requirements stated in 

section 3.3. 

D.  PHYSICAL AND ENVIRONMENTAL HAZARDS: 

Use of this 

equipment in areas with physical or environmental hazards 

may require that additional precautions be taken to reduce 

the possibility of damage to this equipment or injury to the 

user. Hazards may include, but are not limited to: high heat 

(welding or metal cutting), acid or caustic chemicals, corrosive 

environments such as exposure to seawater, high voltage 

power lines, explosive or toxic gases, moving machinery or 

sharp edges. Contact DBI-SALA if you have questions about 

the application of this equipment in areas where physical or 

environmental hazards are present.

E. TRAINING: 

This equipment is to be installed and used by 

persons who have been trained in its correct application and use.

1.4  

Refer to national standards, including; ANSI Z117.1, local, state, 

and OSHA requirements (26 CFR 1910.146), for more information 

on the application of this and associated equipment.

netzerotools.com

netzerotools.com

Summary of Contents for DBI SALA 8518581

























Reviews: