3M Convenience Store D-2400 Installation Instructions Manual Download | Manualshive

Page: 11 / 26

background image

3M Model D-2400

Programming the System

7

Programming the System

Program the system to conform to your planned configuration and desired operation.

Hardware (Jumpers)

Select Call Station(s) to receive ALL CALL and music/messaging during STANDBY mode. (A closed jumper
turns ALL CALL and music/messaging OFF. An open circuit jumper turns ALL CALL and music/messaging ON.)

1.

Use the appropriate jumper to select ALL CALL and music/messaging for each call station.

2.

Jumpers JP1 through JP8 (in order) on the Main Board apply to Call Stations 1 through 8; jumpers JP9 through
JP16 (in order) on the Expansion Board apply to Call Stations 9 through 16.

The locations of the jumpers are shown in Figure 6.

Figure 4. Communications Controller Jumpers

«
...
9
10
11
12
13
...
»

Summary of Contents for Convenience Store D-2400



























Reviews:

No comments

Related manuals for Convenience Store D-2400

Brand: DAB Pages: 8

Brand: M-system Pages: 3

Brand: M-system Pages: 13

Brand: CAME BPT Pages: 8

JBL CINEMA SB130

Brand: Harman Pages: 16

SecurAccess PMR

Brand: Depaepe Telecom Pages: 51

Brand: Bticino Pages: 84

Brand: Peavey Pages: 4

Brand: ICP DAS USA Pages: 8

Brand: KEF Pages: 2

Brand: MESA Electronic Pages: 19

Brand: BAS-IP Pages: 59

Brand: Jaycar Pages: 8

Brand: Legacy Pages: 23

Brand: National Instruments Pages: 16

Brand: IMG STAGELINE Pages: 16

Brand: Bürkert Pages: 48

Traveler TR Series

Brand: Rain Bird Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands