background image

INSTRUCTIONS FOR USING REGENERATION FREQUENCY SCHEDULES: 

(Time clock initiated models only) 

1) 

Determine ADJUSTED HARDNESS by adding three (3) times the iron content in parts per million (ppm) to the hardness in grains per gallon (gpg).  The result-
ing number is ADJUSTED HARDNESS.

 

EXAMPLE:  Hardness is 14 gpg and iron is 2 ppm.  ADJUSTED HARDNESS is 20 gpg (14 plus 3 times 2).

2) 

Select REGENERATION FREQUENCY SCHEDULE corresponding to your model.  Locate box intersected by NUMBER IN FAMILY and ADJUSTED HARDNESS (if 
ADJUSTED HARDNESS is between two numbers in schedule, use higher number).  Number in box represents FREQUENCY or NUMBER OF TIMES PER 12 
DAYS time clock should be set to regenerate.  Refer to HOW TO SET TIME CLOCK REGENERATION CONTROL to set correct frequency. 

EXAMPLE:  You have Model CS1001, 4 in family and 20 gpg adjusted  hardness.  Refer to REGENERATION FREQUENCY SCHEDULE for Model Series 1001 and 
locate box intersected by 4 in family and 20 gpg adjusted hardness.  The fi gure "3" in box indicates a REGENERATION frequency of THREE TIMES PER 12 DAYS 
(if a "1", "2", "4", etc. were in box, frequencies of once twice and four times per twelve days, respectively, would be indicated.)

3-1

SECTION 3:  REGENERATION INSTRUCTIONS

REGENERATION FREQUENCY SCHEDULES

(TIMES PER 12 DAYS)

Model CS1001

Persons

in

Family

Hardness -- GPG

5

10

15

20

25

30

35

40

45

50

55

60

1

1

1

1

1

1

2

2

2

2

2

2

2

2

1

1

2

2

2

3

3

3

4

4

4

6

3

1

2

2

3

3

4

4

6

6

6

6

12

4

1

2

3

3

4

6

6

6

12

12

12

12

5

1

2

3

4

6

6

12

12

12

12

12

12

6

2

3

4

6

6

12

12

12

12

12

12

7

2

3

4

6

6

12

12

12

12

8

2

3

6

6

12

12

12

12

Model CS1501

Persons

in

Family

Hardness -- GPG

5

10

15

20

25

30

35

40

45

50

55

60

65

70

75

1

1

1

1

1

1

1

1

1

1

2

2

2

2

2

2

2

1

1

1

1

2

2

2

2

3

3

3

3

3

4

4

3

1

1

1

2

2

3

3

3

4

4

4

6

6

6

6

4

1

1

2

2

3

3

4

4

6

6

6

6

6

12

12

5

1

2

2

3

3

4

4

6

6

6

12

12

12

12

12

6

1

2

3

3

4

6

6

6

12

12

12

12

12

12

12

7

1

2

3

4

4

6

6

12

12

12

12

12

12

12

12

8

1

2

3

4

6

6

12

12

12

12

12

12

12

9

1

3

4

6

6

12

12

12

12

12

12

10

2

3

4

6

6

12

12

12

12

12

Summary of Contents for Aqua-Pure CS Series

























Reviews: