NOTICE
PURCHASER’S RESPONSIBILITY:
Only health care professionals or other appropriately trained individuals should use this equipment.
Parts Identification
1. Disposable Blade Assembly (9670)
2. ON/OFF Switch
3. Clipper Body (9671)
4. Indicator Light
5. Charger
The 3M Surgical Clipper with Fixed Head 9671 must be used with one
of the following 3M Chargers:
3M Model
Voltage (AC)
9672
Charger
120V, 60Hz US/Canada
9673
Charger
240V, 50Hz Australia/New Zealand (Not UL Approved)
9674
Charger
100V, 50-60Hz Japan (Not UL Approved)
9675
Charger
230V, 50Hz United Kingdom/Ireland
9678
Charger
230V, 50Hz Europe
Clipper Specifications
Transformer Output:
1.3V, 1.91A
Motor Voltage:
1.2 Volts DC
Current without load: 0.58 amps max.
Current with load: 3.18 amps max.
RPM: 5800-8600
Charge Current:
160-210 milliamps
Running Current:
1.2-1.5 amps
Charging Time:
18-24 hours initial, 12-14 hours thereafter
Battery Operating Time:
~45 minutes
Clipper Weight:
201 grams (7.1 oz)
Clipper Dimensions:
14.1 cm (5.55 in) Height
3.8 cm (1.5 in) Width (blade)
3.7 cm (1.46 in) Width (body)
3.4 cm (1.34 in) Depth 11.3 cm (4.45 in)
10.8 cm (4.25 in) Circumference
INSTRUCTIONS FOR USE
To Attach a Disposable Blade Assembly onto the Clipper Body:
Make sure that the ON/OFF switch is in the OFF position. Hold the clipper body at a 45° (degree) angle over the opened blade assembly package. Push the clipper
body into the blade to secure. An audible snap indicates blade assembly is securely attached (A).
To Use the Clipper:
The patient’s skin should be clean. To turn the clipper on, slide the ON/OFF switch to the ON position. Use short, gentle strokes, holding the clipper blade assembly at
a 15 to 30 degree angle to the patient’s skin (B). For best results, clip against the direction of the hair growth. For problem areas, stretch the skin taut while clipping.
To Remove Disposable Blade Assembly:
Assure the ON/OFF switch is in the OFF position. Position the clipper over an appropriate waste receptacle with the blade assembly facing downward. Use your
thumb to push blade assembly off the clipper body into waste receptacle (C).
Care and Cleaning of the Clipper Body:
The housing of the clipper body is made of durable plastic and may be wiped off with a damp cloth containing a small amount of alcohol, disinfectant, or a mild
detergent solution. While uncorded, the clipper body may also be rinsed under running water (D). Allow to dry completely before reconnecting cords or reusing.
Do not immerse clipper body in any liquid (E).
To Charge the Clipper:
1. Slide the ON/OFF switch to the OFF position.
2. Clean the clipper body before reconnecting to the cord, making sure the clipper is free of hair or other contaminants.
3. Connect the cord to the receptacle in the bottom of the clipper and then to an appropriate electrical outlet (120 volts AC 50-60 Hz), making sure the cord is not
pinched or kinked or damaged.
4. The charging indicator light will be on when the clipper is plugged in and making the proper connection. If the charging indicator light fails to illuminate when the
clipper body is plugged in, make sure the cord has proper contact with the clipper terminals and it is free of hair or debris.
5. To be certain that the clipper is fully charged, plug the clipper in for 18 to 24 hours before its initial use. Thereafter, the clipper can be fully charged in
12 to 14 hours.
6. We recommend leaving the clipper plugged in between uses. It cannot be overcharged.
A
B
C
D
E
