Concrete Anchor Straps
User Instructions
If inspection reveals any defect, inadequate maintenance,
or unsafe condition, remove from service and destroy.
Any equipment that has been subjected to the forces
of arresting a fall must be immediately removed from
service and destroyed.
To inspect webbing, bend a portion of the webbing 6-8" into
an upsidedown ‘U’ shape. All webbing must be inspected
for tears, cuts, fraying, abrasion, discoloration, burns, holes,
mold, pulled or broken stitches, or other signs of wear and
damage.
Sewn terminations should be secure, complete, and not
visibly damaged.
All Concrete Anchor Straps must be free of corrosion,
chemical attack, alteration, excessive heating or wear.
All markings must be legible and attached to the product.
Note: Only manufacturer, or entities authorized in
writing by the manufacturer, may make repairs to the
product.
Cleaning and Maintenance
No cleaning or maintenance is required for this product. If
inspection reveals any defect, remove from service.
Installation
Concrete Anchor Straps must be installed on structures
capable of meeting the anchorage strength requirements of
OSHA 29 CFR 1910.66 and 1926.502.
Concrete Anchor Straps may be installed in walls, ceilings,
or fl oors. Attach the Concrete Anchor Strap to the rebar by
either sliding the soft loop over the rebar, or chocking the
soft loop around the rebar. The orientation of the web exiting
poured concrete in a vertical application must be such that the
webbing does not fold over. It must lay fl at as shown in Fig
1. The label on the Concrete Anchor Strap must be viewable
after installation. The anchoring rebar must be at least 4"
(100 mm) from the outside face of the poured concrete.
Concrete Anchor Straps with a protective sleeve must be
installed such that the protective sleeve partially exits the
concrete. Where rebar is exposed and not in poured concrete
the rebar must be #7 or greater with stirrups. The orientation
of the rebar is permitted vertically or horizontally.
Inspection
All Concrete Anchor Straps must be inspected prior to each
use, and additionally by an OSHA defi ned “competent
person” other than the user annually.
Product Label
p
y
y
4" Minimum
Poured Concrete
Wall
Imbedded Concrete
Anchor Strap
Fig. 1
Please recycle. Printed in USA.
© 3M 2012
3M is a trademark of 3M Company,
used under license in Canada.
All rights reserved.
IM-0036B (02-2012) 34-8709-5639-7
3M Occupational Health &
Environmental Safety Division
3M Center Building 235-2W-70
Saint Paul, MN 55144-1000
USA
Technical Assistance: 800-243-4630 in U.S.
and 800-267-4414 in Canada
www.3M.com/FallProtection
www.3M.com/PPESafety
ISO 9001
FM 573368
Product Warranty, Limited Remedy, and Limitation of Liability
WARRANTY:
THE FOLLOWING IS MADE IN LIEU OF ALL WARRANTIES OR CONDITIONS, EXPRESS OR
IMPLIED, INCLUDING THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE. Equipment offered by 3M is warranted against factory defects in workmanship and materials for
a period of one year from date of installation or fi rst use by the original owner.
LIMITED REMEDY:
Upon notice in writing, 3M will repair or replace all defective items at 3M’s sole discretion. 3M reserves
the right to require that the defective item be returned to its plant for inspection before determining the appropriate course of
action. Warranty does not cover equipment damage resulting from wear, abuse, damage in transit, failure to maintain the product
or other damage beyond the control of 3M. 3M shall be the sole judge of product condition and warranty options. This warranty
applies only to original purchaser and is the only warranty applicable to this product. Please contact 3M technical service
department at 800-243-4630 for assistance.
LIMITATION OF LIABILITY:
IN NO EVENT WILL 3M BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL
OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO LOSS OF PROFITS, IN ANY WAY RELATED
TO THE PRODUCTS REGARDLESS OF THE LEGAL THEORY ASSERTED.
