background image

3M

 No Polish Connector, Kit and Tool Descriptions

Product Number

Description

Packaging

8800-APC/AS/AGC

3M No Polish Connector SM SC/APC, AGC, Angle Splice, 250/900-µm

(green housing, green boot, green dust cap)

60/package

8865-AGC

3M

 Fiber Optic Angle Cleave Kit with 3M

 Angled Cleaver 2536-AGC

1/package

2536-AGC

Sumitomo Fiber Optic Angle Cleaver

1/package

8865-AT

3M

 No Polish Connector Assembly Tool for 900 µm connector

1/package

Communication Markets Division

6801 River Place Blvd.

Austin, TX 78726-9000

Phone   1-800-426-8688

Web   www.3M.com/Telecom

Please recycle. Printed in USA © 3M 2018.  

All rights reserved. 78-0015-4562-9-A

3M is a trademark of 3M Company.  All other trademarks herein are the property of their respective owners.

Important Notice

All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the 

accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended 

application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current 

publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an 

authorized officer of 3M.

Warranty; Limited Remedy; Limited Liability. 

This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 

3M MAKES NO OTHER 

WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR 

PURPOSE. 

If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 

3M product or refund the purchase price of the 3M product. 

Except where prohibited by law, 3M will not be liable for any direct, indirect, special, 

incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.

 

Summary of Contents for 2536-AGC











Reviews: