3DR Solo, Manual

Page: 38 / 57

33
Figure 6.1.1.4: Manette - Alerte d’erreur de calibrage
6.1.2 Alertes de service
Les alertes suivantes indiquent une erreur système qui nécessite un entretien. Utilisez l’application pour soumettre
un billet de dépannage à 3DR Support ou contactez un centre de service Solo agréé pour effectuer l’entretien du
Solo et résoudre l’alerte. Une erreur de joystick peut se produire en vol ou avant le décollage. Quand l’erreur de
joystick est reçue en vol, le Solo rentre à la base et atterrit.
Figure 6.1.2.1: Manette - Alertes de service
6.2 Erreurs en vol
Pendant le vol, la manette surveille le signal GPS du Solo, le signal de la manette, le niveau de batterie de vol et le
niveau de batterie de la manette.
6.2.1 Limite d’altitude
Quand Solo atteint la limite d’altitude pendant le vol, il maintiendra et ne dépassera pas cette altitude ; en outre,
la manette affiche l’alerte suivante.
Figure 6.2.1.1: Manette - Alerte de limite d’altitude
6.2.2 Connexion d’application
La manette affichera les alertes suivantes sous la forme d’une bannière en cas de connexion ou déconnexion de
l’application Solo du Solo. Une connexion active permanente au Solo est recommandée pendant le vol. Référez-
vous à la section 2.6 pour se connecter au réseau Wi-Fi du Solo via l’application. Le Solo ne retourne pas à la base
si la connexion à l’application est perdue pendant le vol.
ARMING ALERTS
Altitude calibration
System self-calibrates altitude after altitude disparity
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in “sensor error” screen)
Calibration error
Please restart Solo
Compass error
User is asked to use Solo app to calibrate.
Alert persists until:
User completes calibration using the app (system then continues sensor check)
User powers off controller, or Solo
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Calibrating compass
Please wait
Level error
User is asked to use Solo app to calibrate
Alert persists until:
User complete calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Uneven surface
Move Solo to a level surface
Altitude calibration
System self-calibrates altitude after altitude disparity
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in “sensor error” screen)
Calibrating Solo
Please wait
Compass error
User asked to use Solo app to calibrate.
Alert persists until:
User completes calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Throttle too high
This flight mode requires low
throttle before starting motors
Catch-All
Remaining rare but problematic APM errors
will be captured under a catch-all for
logging trouble tickets
Service required
Use 3DR Solo app to log a trouble
ticket with customer support
PREARM SENSOR ERRORS
Altitude calibration
System self-calibrates altitude after altitude disparity
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in “sensor error” screen)
Altitude calibrating
Please wait
Compass error
User asked to use Solo app to calibrate.
Alert persists until:
User completes calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Compass error
Please calibrate compass using
the 3DR Solo app
Level error
User is asked to use Solo app to calibrate
Alert persists until:
User complete calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Level error
Please calibrate level
using the 3DR Solo app
Sensor error screen
For sensor errors requiring user-initiated restart
Sensor error
Please try and restart Solo
Battery unknown
Displayed if Artoo is powered on with a battery has an
ID resistor unknown to Artoo. (Not logged in current software version’s index.)
HAPTIC: Strong feedback, 40 millisecond pulse
After Solo is disconnected, Artoo should display “waiting for Solo”
Unknown battery
Battery % not be accurate
?
Dismiss
Control sticl error
Persists until:
Controller starts with stick values in range.
Control stick error
Contact 3DR customer support
IN-FLIGHT ALERTS: CONTROLLER RELATED
RC Failsafe
Controller signal lost, RTH screen
Alert persists until:
TIMEOUT: 5000 milliseconds
Controller signal lost
Solo will return home
RC Signal Recovered
User can press Fly to recover
Alert persists until:
User presses Fly and enters Fly mode
HAPTIC: 40millisecond so user is aware that they can take control
RC Failsafe (No GPS)
Controller signal lost,
emergency land screen
Alert persists until:
TIMEOUT: 5000 milliseconds
Controller Value out of Range
User is asked to contact customer support
Alert persists until:
TIMEOUT: 5000 milliseconds
go to persistent hint-box message
(persistent until reboot)
Control stick error
Solo will return home
Signal recovered
Controller signal lost
Emergency landing started
324
FT
84
FT
HOME
48
%
FLIGHT BATTERY
ALTITUDE
Return Home
12
Control stick error
Contact 3DR Support after landing
Camera paddle and dial failure
Alert triggered on input error on the paddle
or tilt speed dial potentiometers
TIMEOUT: 5000 milliseconds
Control stick error
Solo will return home
324
FT
84
FT
HOME
48
%
FLIGHT BATTERY
ALTITUDE
FLY
12
Manual camera controls error
IN-FLIGHT ALERTS
Maximum Altitude
User is told that maximum altitude has been reached
Vehicle is not able to go higher than max altitude
Alert appears once per flight and is triggered at 100 FT by default.
Alert persists until:
TIMEOUT: 5000 milliseconds
HAPTIC: Double buzz 40-40 millisecond
Maximum altitude
Preset max altitude reached
Crash Detected
User can use app to log a support ticket
Alert persists until:
User presses A
HAPTIC: Quad buzz: 40-40-40-40
Solo SFX: Start lost call ping if more than 10 m away
Crash detected
GPS signal lost (Switches to FLY: Manual)
Alert persists until:
TIMEOUT: 3000 milliseconds
HAPTIC: Triple buzz twice: 30-30-30, 30-30-30
GPS lost
Switching to manual control
GPS signal recovered
(User who has either advanced mode enabled, or manual set to A or B)
(When home is already set)
Switches to FLY form Fly:Manual when user presses Fly
Alert persists until:
TIMEOUT: 3000 milliseconds
GPS ready
Press to dismiss
FLY
Press for GPS control
GPS signal recovered
(No advanced mode, Manual mode not set to A or B)
Switches to FLY when GPS is recovered
Alert persists until:
TIMEOUT: 3000 milliseconds
HAPTIC: 40 millisecond buzz for awareness
GPS ready
GPS signal established
(User took off without GPS, no home position, regardless of advanced modes)
Alert persists until user sets home
HAPTIC: 20 milliseconds every 3 seconds until press
GPS found
FLY
Press to set home
Switching to FLY
ARMING ALERTS
Altitude calibration
System self-calibrates altitude after altitude disparity
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in “sensor error” screen)
Calibration error
Please restart Solo
Compass error
User is asked to use Solo app to calibrate.
Alert persists until:
User completes calibration using the app (system then continues sensor check)
User powers off controller, or Solo
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Calibrating compass
Please wait
Level error
User is asked to use Solo app to calibrate
Alert persists until:
User complete calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Uneven surface
Move Solo to a level surface
Altitude calibration
System self-calibrates altitude after altitude disparity
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in “sensor error” screen)
Calibrating Solo
Please wait
Compass error
User asked to use Solo app to calibrate.
Alert persists until:
User completes calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Throttle too high
This flight mode requires low
throttle before starting motors
Catch-All
Remaining rare but problematic APM errors
will be captured under a catch-all for
logging trouble tickets
Service required
Use 3DR Solo app to log a trouble
ticket with customer support
PREARM SENSOR ERRORS
Altitude calibration
System self-calibrates altitude after altitude disparity
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in “sensor error” screen)
Altitude calibrating
Please wait
Compass error
User asked to use Solo app to calibrate.
Alert persists until:
User completes calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Compass error
Please calibrate compass using
the 3DR Solo app
Level error
User is asked to use Solo app to calibrate
Alert persists until:
User complete calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Level error
Please calibrate level
using the 3DR Solo app
Sensor error screen
For sensor errors requiring user-initiated restart
Sensor error
Please try and restart Solo
Battery unknown
Displayed if Artoo is powered on with a battery has an
ID resistor unknown to Artoo. (Not logged in current software version’s index.)
HAPTIC: Strong feedback, 40 millisecond pulse
After Solo is disconnected, Artoo should display “waiting for Solo”
Unknown battery
Battery % not be accurate
?
Dismiss
Control sticl error
Persists until:
Controller starts with stick values in range.
Control stick error
Contact 3DR customer support