3DHS SLICK 580 Assembly Manual Download Page 15

25.  If using the included Side Force Generators now is the time to mount 
them.  Each SFG mounts using 2 wood screws.

Set-up and flying tips

The CG for the Slick 580 is on the wing tube.  There is plenty of room on the 
battery tray to move your battery to achieve this CG location.  Depending on 
your flying style you can adjust the position of the battery to alter the CG to 
accommodate your preferences.  For this type of aircraft where I am going to 
predominantly fly aggressive 3D I typically set the airplane up with a neutral 
CG, meaning that when the aircraft is flown inverted straight and level it 
requires no down elevator to maintain altitude.  If your flying style leans more
toward precision aerobatics then I recommend setting your CG using the 45 
degree line test.  Fly the aircraft from left to right or right to left, whichever 
direction you are more comfortable with at 3/4 to full throttle.  Pull the 
aircraft to a 45 degree up line and establish this line and immediately roll the 
aircraft inverted.  Establish this line and let go of the elevator stick.  Ideally 
the aircraft will continue to track on that 45 degree line for several hundred 
feet before slowly starting to level off.  Adjust the position of your battery to 
achieve this flight condition.  Once satisfied with the location of your CG 
scribe a mark on the battery tray so that you can position the battery in the 
same location each flight and achieve the same feel and flight characteristics 
each flight.

I also highly recommend taking the time to properly set up your rates and 
exponential settings.  Setting up low rates for precision maneuvers and high 

15

Summary of Contents for SLICK 580

















Reviews: