3D Systems Viper Pro SLA User Manual Download

Page: 80 / 121

www.3dsystems.com

Platform Installation

The RDM must be in the machine before this process starts. When correctly installed, the platform
sits on the elevator platform mount.

5. Go to the Control Panel, select a part,
and start a build.
6. When correctly installed and started, the
elevator main stage moves to the Build Start
position.

Note: The

manual operation

is an

alternate method to move the platform
to the build start position. With this,
the user can also remove bubbles prior
to starting a new build.

1. Make sure that the elevator motion stage is at its offload
position.
2. Place the platform on two

L-shaped guides

in the rear

of the RDM.
3. Push the platform against the

front platform guides

4. Make sure that the

notches

in the platform engage into the
front platform guides.

70696 Revision 1C 27-Aug-08

Summary of Contents for Viper Pro SLA


























































































































Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands

3D Systems Viper Pro SLA, User Manual

Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands