3D Systems Viper Pro SLA User Manual Download

Page: 66 / 121

www.3dsystems.com

m a c h i n e w i n d o w

user

’

s manual

Machine Window

Status

Status

enables you to display the properties of the resin delivery

module (RDM), as well as the available laser power.

Resin:

Displays the resin name.

Vat Size:

Displays the build capacity of the RDM.

Temp:

Displays the current vat temperature.

Displays the current air temperature.

Level:

Shows the current resin level.

Power:

Shows the maximum available laser power.

Laser:

Displays if the laser is on or off.

LW Hrs:

Displays the number of warrantee hours the laser has run.

Shutter:

Displays status of the laser safety shutter (open/closed).

Note: These windows are not updated during a build. If
the laser is turned on or the shutter is opened by the
build process, the status shown may be incorrect.

Door Interlock:

Displays if all door interlocks are closed.

ByPassKey Enable:

Displays if the interlock bypass key is active.

Software Overview

70696 Revision 1C 27-Aug-08

Summary of Contents for Viper Pro SLA


























































































































Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands

3D Systems Viper Pro SLA, User Manual

Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands