3D Systems Viper Pro SLA User Manual Download

Page: 59 / 121

Laser

Laser On:

Toggles the laser on or off, by either check (on) or uncheck (off).

Shutter:

Toggles safety shutter open or closed, by either check (open) or uncheck (closed).

Small Spot:

Sets IPM to the small spot focus position.

Large Spot:

Sets IPM to the large spot focus position.

Set Laser Power:

Sets Laser Power (in milliwatts mW) to the value that is in the power field, if

achievable.

Get Power at Vat:

Directs beam to the Full Area Detector (FAD) and determines the power, in

milliwatts, as measured by the FAD.

Recalculate Power Coeff:

Adjusts the power calibration for the decline of laser power over time.

This option is available here, but is not necessary for the user to perform. This function is
accomplished each time the laser power is set.

70696 Revision 1C 27-Aug-08

Summary of Contents for Viper Pro SLA


























































































































Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands

3D Systems Viper Pro SLA, User Manual

Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands