manualshive.com logo in svg

3Com VCX V7000, Maintenance Manual

The 3Com VCX V7000, a cutting-edge communication solution, empowers businesses with seamless connectivity. Maximize its potential by accessing the comprehensive User Manual, available for free download from manualshive.com. Discover step-by-step instructions, troubleshoot common issues, and unlock the full potential of this exceptional product.

Share
Download
background image

260

A

PPENDIX

 C: U

PGRADING

 VCX S

ERVER

 S

OFTWARE

 F

ROM

 V6.0 

TO

 V7.0

VCX software (for example, 

vcx-all-7.0.3c.tar)

 that will replace 

version 6.0. The letter 

c

 is always appended to the version number.

Next, execute the following steps in the order listed:

■

Upgrade the primary VCX server. See 

Upgrading the Primary VCX 

Server

.

■

Upgrade the secondary VCX server. See 

Upgrading the Secondary VCX 

Server

.

■

Set up database replication on the primary VCX server. See 

Set Up 

Database Replication

.

Upgrading the

Primary VCX Server

Follow the steps in this section to upgrade the primary VCX server.

1

To start the upgrade process, enter these commands on the primary VCX 
server: 

cd /opt/installtemp

tar xvf vcx-all-7.0.

x

c.tar

cd upgrade-7.0.

x

c 

./install-upgrade

The system may prompt you to confirm that a new operating system 
version will be installed and indicates which disk partition will be used 
after the upgrade. If you see such a prompt, answer 

y.

The system displays several status messages. The last two messages are:

------------------- Installation Completed Successfully -------------------

------------------- VCX version 7.0.

x

c is now available -------------------

2

Obtain a license key for the server. See 

Obtaining a License Key File

.

3

Install the license key. See 

Installing a License Key File

.

4

Switch to the new software version by entering the following command:

vcx-switchversion 7.0.

x

c 

The system displays several status messages and then reboots. After the 
the reboot process has been completed, the system starts VCX 7.0.

x

 

services.

5

After the system has completed the restart process, verify that the 
upgrade has occurred by entering this command:

ls -l /opt/3com/VCX

Summary of Contents for VCX V7000

























































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7000

Archos S3 Platinum User Manual preview
S3 Platinum
Brand: Archos Pages: 115
Fysic FM-7600 User Manual preview
FM-7600
Brand: Fysic Pages: 60
Excelltel IPH305(P) Quick User Manual preview
IPH305(P)
Brand: Excelltel Pages: 2
Viking K-1900-8-IP Product Manual preview
K-1900-8-IP
Brand: Viking Pages: 25
Sonim XP5520 Bolt User Manual preview
XP5520 Bolt
Brand: Sonim Pages: 89
Samsung Vibrant User Manual preview
Vibrant
Brand: Samsung Pages: 193
Samsung SGH-T839 Manual Del Usuario preview
SGH-T839
Brand: Samsung Pages: 259
Samsung SGH-T999 User Manual preview
SGH-T999
Brand: Samsung Pages: 365
Samsung SGH-T519 - Trace Cell Phone User Manual preview
SGH-T519 - Trace Cell Phone
Brand: Samsung Pages: 210
Samsung SM-A145F User Manual preview
SM-A145F
Brand: Samsung Pages: 119
Samsung SM-A155F Repair Manual preview
SM-A155F
Brand: Samsung Pages: 125
Samsung SM-A127F/DS User Manual preview
SM-A127F/DS
Brand: Samsung Pages: 104
Samsung J7 Star User Manual preview
J7 Star
Brand: Samsung Pages: 145
Samsung GT-I9060L/DS User Manual preview
GT-I9060L/DS
Brand: Samsung Pages: 125
Samsung Glyde Glyde User Manual preview
Glyde Glyde
Brand: Samsung Pages: 156
Samsung I8910HD User Manual preview
I8910HD
Brand: Samsung Pages: 78
Zte F160 User Manual preview
F160
Brand: Zte Pages: 89
Citizen CVVB-M293-N1 Manual preview
CVVB-M293-N1
Brand: Citizen Pages: 7

Brands by name

Popular brands

Load more brands