3Com VCX V7000 Maintenance Manual Download | Manualshive

Page: 234 / 344

background image

234

A

PPENDIX

B: U

PGRADING

VCX S

ERVER

S

OFTWARE

F

ROM

V7.1.

X

TO

V7.1.

Y

Upgrading a
Multi-Site VCX
System with Branch
Offices

Some multi-site VCX systems have regional offices and branch offices.
Each branch office is associated with a regional office.

Multi-site VCX systems can be categorized by the method used to
implement messaging.

■

In a multi-site VCX system configured to use

local

messaging, the IP

Messaging server is co-located with the IP Telephony server at each
branch office. In this case, each branch office provides messaging
services for its users.

■

In a multi-site VCX system configured to use

global

messaging, the IP

Messaging server is located on the regional office. Each branch office
runs the IP Telephony server only. In this case, the regional office
provides messaging services for users at each branch office.

■

In version 7.1 multi-site VCX systems, you can configure branch and
regional sites to use Global Voicemail Integration. Each location must
be running IP Messaging services, which means that, in a multi-site
system configured to use global messaging, you cannot enable Global
Voicemail Integration on a branch. You can, however, enable Global
Voicemail Integration on the region providing IP Messaging services to
the branch.

This service is provided by a pair of Global Voicemail Central Servers
(GVCS) to enable global voicemail integration on an entire IP
Messaging system.

A GVCS coordinates mailbox creation and mailbox updates on
regional and branch office IP Messaging servers. You must install IP
Messaging software on a GVCS, and then set up the GVCS through
the IP Messaging administrator configuration interface

before

enabling global voicemail integration on regional and branch office IP
Messaging servers. Refer to the

IP Messaging Module Operations and

System Administration Guide

for more information and for

configuration options.

Once you have installed and configured a GVCS, you can add existing
IP Messaging servers to the Global Voicemail Integration system by
running the

vcx-reconfigure

command on each server (see

Follow the procedures in this section to upgrade a multi-site VCX system
from version 7.1.

x

to 7.1.

y

. The components in a multi-site VCX system

can be set up in many possible configurations. The procedures in this

«
...
232
233
234
235
236
...
»

Summary of Contents for VCX V7000

























































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7000

Brand: Samsung Pages: 155

Brand: Sony Ericsson Pages: 85

Brand: Quadro Pages: 125

Brand: M4 Pages: 22

Brand: Alcatel Pages: 121

Brand: myPhone Pages: 79

Brand: Hisense Pages: 33

Brand: Xiaomi Pages: 50

Brand: Xiaomi Pages: 101

Brand: Lava Pages: 2

Brand: Nokia Pages: 2

Brand: Nokia Pages: 2

Brand: Nokia Pages: 2

Brand: Nokia Pages: 2

Brand: Nokia Pages: 29

6131 - Cell Phone 32 MB

Brand: Nokia Pages: 289

Brand: Zte Pages: 28

Brand: Philips Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands