3Com VCX V7000 Maintenance Manual Download | Manualshive

Page: 200 / 344

background image

200

A

PPENDIX

A: U

PGRADING

VCX S

ERVER

S

OFTWARE

F

ROM

V7.0

TO

V7.1

Telephony and Messaging Server

for more information. In this

example, there is one Master site, Region 1.

c

The

Enter the MASTER DEFINITION SITE IP Address [

IP

address

]

prompt appears.

Enter the IP address of the Master Definition site. This is the IP address
of the eth0 interface on this server (the Authentication and Directory
server in Region 2).

d

The

Enter the MASTER SITE 1 IP Address [0.0.0.0]

prompt

appears.

Enter the IP address of the Master Site. This is the IP address of the
eth0 interface on the Authentication and Directory server in Region 1.
If there are more than one Master Sites, this question repeats until the
number of master sites specified in step

b

is reached.

e

The

Do you want to continue with the above settings? [n/y]:

prompt appears.

Enter

y

to continue. The script executes.

When the replication is complete,

Multi-Master Replication Status

is

reported as

NORMAL

. Do not continue to the next step on this server

until the replication is complete. Note that replication can take
approximately 20 minutes to complete.

f

You can check the replication by entering the following command:

./checkReplication

7

Once replication is complete and status is

NORMAL

on Region 1 and

Region 2, start the Authentication and Directory servers in each region by
entering the following commands while logged in as

root

:

cd /opt/3com/VCX/scripts/rc3.d

./S20vcxdata start

8

Start the Tomcat process on the primary Call server and the secondary
Call server in each region by entering the following commands:

cd /opt/3com/VCX/scripts/rc3.d

./S70tomcat start

Upgrading the

Regional IP

Messaging Servers

This section describes how to upgrade regional IP Messaging servers.
These servers may provide messaging services for users using one of the
following methods:

■

Global Voicemail Integration — In version 7.1, multi-site VCX systems
can be configured to use Global Voicemail Integration. This service is

«
...
198
199
200
201
202
...
»

Summary of Contents for VCX V7000

























































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7000

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 312

Brand: Panasonic Pages: 311

Brand: Samsung Pages: 78

Brand: T-Mobile Pages: 29

Brand: Manta Pages: 20

One Touch Spop 4030D

Brand: Alcatel Pages: 73

Digital Mova SO503iS HYPER

Brand: Docomo Pages: 396

Brand: Pantech Pages: 70

Brand: HTC Pages: 4

Brand: Samsung Pages: 49

Brand: Zte Pages: 60

Brand: Xiaomi Pages: 1

Brand: Zte Pages: 79

Brand: GENERAL MOBILE Pages: 65

Brand: Zte Pages: 114

Brand: Philips Pages: 2

Desktop 9850/52

Brand: Philips Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands