3Com VCX V7000 Installation Manual Download | Manualshive

Page: 322 / 488

background image

322

C

HAPTER

9: I

NSTALLING

D

EVICES

5

On any of the IBM servers, press the start button. This is not necessary on
the V6000 server.

6

When the server has finished the startup process, log in as root and run
this command:

vcx-raid-setup

7

When the script asks you whether you want to continue, answer

Y.

The script stops VCX services, configures the new disk as a RAID device,
and copies the contents of the original disk to the new disk. It then
reboots the server.

After the reboot, the process of mirroring the two disk drives continues in
the background. The system is fully operational.

Verifying RAID Status

You can determine the status of the RAID disks by using the

vcx-raid-status

command. You might want to determine if the newly

added disk is fully mirrored, or, during later operation, you might want to
verify that both disks are operating properly. Use one of these command
formats:

vcx-raid-status --verbose

vcx-raid-status --short

For instructions on how to replace a failed RAID disk, see

VLAN
Configuration

If you use Virtual LANs (VLANs) in your network, you can configure 3Com
telephones and other devices to operate on a specific VLAN in these
ways:

■

Configure Option 184 on your DHCP server to pass VLAN information
to devices. See

,

“Configuring Option 184 on a Windows

2000 DHCP Server”

for instructions.

■

Manually configure the VLAN ID number on the telephone or device.

Configuring Devices

for VLAN Operation

This section contains instructions on how to configure certain VCX
devices for VLAN operation.

«
...
320
321
322
323
324
...
»

Summary of Contents for VCX V7000









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7000

Brand: Unify Pages: 2

OpenScape CP400

Brand: Unify Pages: 2

Brand: Alcatel Pages: 73

Brand: AGM Pages: 11

8100 SMARTPHONE

Brand: Blackberry Pages: 230

Brand: FLY Pages: 33

Brand: Movilnet Pages: 26

Brand: Doro Pages: 5

Corded IP Phones

Brand: Swissvoice Pages: 12

Brand: 2N Pages: 180

Brand: SoftBank Pages: 19

Brand: 2N Pages: 12

Brand: Zte Pages: 89

Brand: Kyocera Pages: 148

Brand: Geemarc Pages: 56

Brand: Zte Pages: 2

cricket Prelude 2

Brand: Zte Pages: 67

Brand: Haier Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands