3Com Switch 7754 Installation Manual Download

Page: 20 / 80

HAPTER

1: S

WITCH

7750 C

OMPONENTS

48-port 100BASE-X SFP

Module

The 48-port 100BASE-X SFP module provides 48 100 Mbps full-duplex Ethernet
optical ports.

Figure 14 illustrates the 48-port 100BASE-X SFP module.

Figure 14

48-port 48-port 100BASE-X SFP Module

Figure 15 illustrates the front panel and LEDs of the 48-port 100BASE-X SFP
module.

Figure 15

Front Panel of the

48-port 48-port 100BASE-X SFP

Module

Ethernet port

Ethernet port LED

Table 24 describes the 48-port 100BASE-X SFP module LEDs.

Table 25 describes the specifications of the 48-port 100BASE-X SFP module.

Compliance

1EEE 802.3ab

1EEE 802.3

1EEE 802.3u

1EEE 802.3x

1EEE 802.1p

1EEE 802.1D

1EEE 802.1Q

1EEE 802.1X

1EEE 802.1s

1EEE 802.1w

Table 23

Specifications for the 48-port 10/100/1000BASE-T Module (continued)

Specification

Description

Table 24

48-port 100BASE-X SFP

Module LED

LED

Description

LINK/ACT

Green — The port is connected.

Off — The port is not connected.

Green flashing — Data is being transmitted or received.

Table 25

Specifications for the

48-port 100BASE-X SFP

Module

Specification

Description

CPU

MPC8241

BootROM

512 KB

SDRAM

128 M

3C16888

1 2

3C16888

Summary of Contents for Switch 7754

















































































Search results

Summary of Contents for Switch 7754

Reviews:

Related manuals for Switch 7754

Brands by name

Popular brands

3Com Switch 7754, Installation Manual

Search results

Summary of Contents for Switch 7754

Reviews:

Related manuals for Switch 7754

Brands by name

Popular brands